Secon battery monitor
@eyber wrote: Hi. I have diy x8 octo. I have dual 6s 10000mah lipo and 3s 2200mah lipo. I will use 3s lipo with 3dr power modul for gimbal etc.. But I dont know wiring battery to pixhawk ADC 13pin,...
View ArticleNo way to get autotest.py running
@Diego_Diaz wrote: Hi everybody ¡, I've been looking for a solution for several days, but I'm not able to fix it. I've install all stuff related to ArduPilot, following, step-by-step this two guides...
View ArticleAuto Tune 3.5-rc3 from Position Hold
@iseries wrote: Did an auto tune today just to see how it worked. Very scary experience. I took off and set Auto tune in motion. It seem as though it wanted to hug the near by trees for some reason....
View ArticleSpinning while in AUTO mode - declination?
@charles_linquist wrote: I'm using APM 3.2.1 and have my magnetic declination set to ~13 degrees. The craft was flying fine.I traveled to another country and attempted to do an AUTO flight there. The...
View ArticleDrops/flips over the front motor, why?
@JabbaDos wrote: Guys, I have a strange thing with pixhawk 3.4.6. A quad plus config, 3S, mn3110-780, 25A ESC, flies well at the beginning in stabilize. After 2-3 minutes it drops, flips over the...
View ArticlePrecision Loiter, IR-LOCK + Autotune?
@megabotz69 wrote: I saw in the Copter 3.5 rc1 announcement that precision loiter with the IR-LOCK sensor is available. Also seeing folks mention considerable drift during autotune. I had my own...
View ArticleAltitude issue using SF11/C Lidar
@arifg wrote: I have a copter under 3.5.0-rc2 with SF 11/C lidar installed. I have an issue with altitude flying both Auto and manual Position Hold missions. The problem is that the vehicle suddenly...
View ArticleAdding and controlling a Samsung NX camera with the Pixhawk
@BigAl wrote: It's been great getting to know about the Pixhawk, its many unique and customizeable features, and especially, flying the quad. Recently, and with thanks to those on this forum who have...
View ArticleCommunicating with Payload over CAN Bus
@ferocity02 wrote: Hello, I am interested in having my Pixhawk 1 communicate with a payload over CAN bus. As a first step, I would like the Pixhawk to 'listen' to the CAN messages and record such data...
View ArticleMOT_HOVER_LEARN - LearnAndSave
@Thorsten wrote: Checking some parameters I came across MOT_HOVER_LEARN. I usually set it to 1. But now I figured that there seem to be three options: 0:Disabled1:Learn2:LearnAndSave I am wondering...
View ArticleINS_TRIM_OPTION question
@Pedals2Paddles wrote: Value Meaning0 Don’t adjust the trims1 Assume first orientation was level2 Assume ACC_BODYFIX is perfectly aligned to the vehicle Looking for advice on the right setting for...
View ArticleFAA number place holder
@iseries wrote: Is there any plans to be able to store the FAA number in a field for later use? It seems that identification at some point may need to be transmitted or viewed. Mike Posts: 2...
View ArticleEKF3 Waiting for GPS config data
@smithy wrote: Hi all, I have a small quad with Copter-3.5-rc3, I am constantly getting "EKF3 waiting for GPS data" does anyone have anydea how to sold the error? Thanks Posts: 7 Participants: 4 Read...
View ArticleOdd behavior on 3.4.1 from Drift mode
@DaveP wrote: I flew my HC 550 hex this morning to test all the flight modes switching from altitude hold to GPS mode etc.When I tried drift mode the craft responded very well, so I switched back to...
View ArticleSD card corruption due to crash or crash due to SD card corruption?
@panky wrote: Yesterday I set up my Tarot680 with autotune and some flight tests and my hexacopter did fine (a short clip from yesterday here)my internal compass was fine except when flying backwards...
View ArticleEKF Error Compass Variance, suddenly, until I land
@Matt_tt wrote: Hello all, I'm having an issue with my setup. I'm using S1000 frame and PH1, with V3.4.6 Octa FW. First issue is that when y try to calibrate compass, after doing a proper accel...
View ArticlePixhawk on solo reset in midflight... or something like that?
@Pedals2Paddles wrote: I'm not sure what to make of these two incidents. First Incident: I had it out hovering letting the battery run down. I wanted to test the battery failsafes. When the failsafe...
View ArticleUnable to choose airframe on BeagleBone Blue
@karthik wrote: Hi, I got my BeagleBone Blue a couple of days ago, and so far I've gotten ArduPilot running on the blue based on @mirkix 's instructions on the git...
View ArticlePixHawk with DJI E310...help!?
@lobohobo wrote: So, this is my first build...ever. A friend gave me an "old" F450. I kept the E310 ESCs and 2312 motors and I've replaced everything naza with a PixHawk FC, a PH compatible GPS,...
View ArticleWaypoint controller produces a large target position delay
@arsene wrote: Hello, guys, I'm trying to write a self-defined trajectory and utilize the guided mode to let the quads track this trajectory by writing a 2-HZ loop such that each time a new waypoint...
View Article