Quantcast
Channel: ArduCopter - ArduPilot Discourse
Browsing all 21330 articles
Browse latest View live

Quadcopter won't lift

@mark_lester_Magno wrote: already done with mandatory configuration esc are all calibrated but the it won't lift up the throtlle is in the middle but still not lifting all the props are mounted...

View Article


Image may be NSFW.
Clik here to view.

Pixhawk AutoTune crash

@Thi1231 wrote: Hello, My hexacopter crashed a few days ago and I cannot find out why exactly. It was after I tried to autotune it, I don’t know if it could be the reason. Here is a list of things I...

View Article


Copter 3.5 rc2 rtl strange behaviour

@AJack wrote: After a successful mission that is suposed to end with RTL from the set altitude copter starts climbing.Rtl_cone_slope 3, rtl_climb_min 0 with rtl_climb_min = 0 isnt supposed to stay to...

View Article

Ch9 & ch10 flysky

@a4avant wrote: In english with google translator (I'm spanish) : Hello, I have a 10-channel flysky fs-i6s and a 10-channel receiver, the flysky fs-ia10b, in my pixhawk, but when I try to calibrate...

View Article

Need help with setting up switch on Radio Transmitter

@BigAl wrote: I have a DJI F450 copter with a Pixhawk. I am using a FlySky FS-T6 transmitter and FS-R6B receiver. The receiver connects to the Pixhawk using a PPM Encoder. The copter is working well...

View Article


APM 2.5-multicopter with 3.2.1 all over the place

@MickeM wrote: Hi, I had a small DJI F450 quad with an APM 2.5-kit (3DR APM 2.5, 3DR GPS/Compass uBlox 7, 3DR PM, 3DR Telemetry) and with firmware 3.2.1 (the latest for APM). LiPo between plates, APM...

View Article

Pixhawk autotune fail and crush

@sakirpolay wrote: Hello, My quadcopter crashed today while first autotuning attept and I could not find out why exactly dad happened. this was first autotune, it made 4-5 twitch in roll axis and...

View Article

Couldn't launch Mission Planner

@chris661 wrote: Hi, when I try to launch MP I have Not responding message. And after some time, I have a message from MP telling me that I have to activate a service and put a parameter on 1 with...

View Article


Image may be NSFW.
Clik here to view.

Problem on uploading AHRS_test.pde on the APM

@spirit wrote: I attached Ultrasonic Sensor and gimbal servo on my S550 Copter. the servo will fix sensor's direction when drone tilt forward when it is flying. So I must get drone's AHRS Data(Pitch...

View Article


No PWM outputs Ch8-Ch16. Advise please

@Fettler wrote: Hi.Im trying to add a seagull camera controller to my pixhawk setup. When I monitor RCin in on the various channels I want to use (like AUX1, RC9) there is the correct PWM signal but...

View Article

AltHold mode running KDE

@copilot wrote: Hi I am busy building a new X8 using KDE motors and their UAS55HVC ESCs. These ESCs does not normally require calibration but when using them with the Pixhawk it is recommended to buy...

View Article

Image may be NSFW.
Clik here to view.

APM V3.1 Channel in and Channel out

@tomerinbar1 wrote: Hello All, I've a problem that I can't find any solution for it. After I arm the board and rise the throttle it's jump to pwm 2028 on the ch1,2,3,4out. It's just jump straight away...

View Article

Terrain data - When is it deleted off the Pixhawk?

@Pedals2Paddles wrote: From reading the guides on Terrain data, I completely understand how it decided what terrain data to request from the ground station. And I get that it stores it on the Pixhawk...

View Article


Optical flow behaving badly indoors (possible rangefinder issue?)

@ollenorelius wrote: I'm trying to fly a quadcopter autonomusly indoors using a optical flow sensor, but I'm getting quite erratic results trying to fly in Loiter. I've followed the guide from the...

View Article

Image may be NSFW.
Clik here to view.

HELP: Battery Failsafe Crash

@crazy1pilot wrote: Hi All, I recently encountered a problem that has me a little puzzled and I am hoping someone can help me figure out the cause. a few days ago I was adding the finishing touches on...

View Article


PX4Flow position estimation

@Nafnaf wrote: Hi, is there a log parameter to view the position/path of the drone, which is estimated by integrating the optical flow velocities? Thanks! Posts: 1 Participants: 1 Read full topic

View Article

Loss of control and warnings after power cycling

@jamescooper1 wrote: Trying to figure out what may have caused a series of faults ending up contributing to a crash. Background: We have been testing a sense and avoid system utilizing the TX board...

View Article


Image may be NSFW.
Clik here to view.

When autotune becomes a crash test

@Carpenter wrote: Hi, I'm a fan of ArduCopter for a number of months now, I've trying to build a copter dedicated to photogrammetry on an Alien GF680 frame.Step by steps reading the wiki and the forum...

View Article

About "terrain follow" question?

@zhitao wrote: Hi,all the link:http://ardupilot.org/copter/docs/terrain-following.html#terrain-following , have the passage below: Terrain FollowingCopter 3.4 (and higher) support “terrain following”...

View Article

Pixracer buzzer very quiet

@Anthony_Short wrote: I have an AUAV Pixracer running AC 3.4.6. I'm very happy with it, except the buzzer (came with the flight controller) is extremely quiet. I can only hear it indoors. The grass is...

View Article
Browsing all 21330 articles
Browse latest View live