Quantcast
Channel: ArduCopter - ArduPilot Discourse
Browsing all 21347 articles
Browse latest View live
↧

Arm / disarm issues

@scostic wrote: Problem resolved. it will be deleted. thank you Posts: 2 Participants: 2 Read full topic

View Article


RX connection Dropping

@jtroutt19 wrote: I am having an issue and am not sure why it is happening. I switch flightcontrollers from librepilot revolution to the pixhawk. I also have the 915mhz telemtry radio other those 2...

View Article


Image may be NSFW.
Clik here to view.

Does ardupilot v3.42 support the external mpu9250?

@jane wrote: I connected mpu9250 on external spi port, then L3GD20 failed. If the external MPU9250 was removed,everything is ok!Does ardupilot v3.42 support the external mpu9250?Anyone know about...

View Article

SBUS issues with a specific receiver

@StevenCoral wrote: Hello all,I have scoured the net only to find the last mention of this issue dating back to march, 2016 (which isn't long ago) on this very forum.I am using a Futaba 14SG...

View Article

Image may be NSFW.
Clik here to view.

School Project, Advice needed! APM 2.6

@Mart_Fabi wrote: Hey guys, a group of friends and I are planning to use the APM board 2.6 to control a Quadcopter that we are building for school. Since we are all new to the RC space I wanted to ask...

View Article


Copter-3.4.3 released!

@rmackay9 wrote: Copter-3.4.3 has become the default official version deployed through the ground stations. There are a few important fixes vs 3.4.2 so we strongly recommend that people upgrade. 1)...

View Article

RSSI Pixhawk PX4 & FrSky X8R Receiver

@onthelearningcurve wrote: It's that thorny old problem that so many pilots have trouble with - getting RSSI to work!So, I have a Pixhawk PX4 and FrSky X8R Rx and Taranis X9D Plus Tx.This is what I...

View Article

Solid yellow LED when trying to calibrate ESCs?

@DREW8110 wrote: I built a 600mm quadcopter with a Pixhawk flight controller. When trying to calibrate the ZTW Spider 30 amp Opto esc's, I get a solid yellow LED from the pixhawk. I put transmitter...

View Article


Do-Digicam-Control does not work after landing

@Rocket wrote: I need help please. I have a mission in which the quad lands at a waypoint, then needs to take a photo using "Do-Digicam-Control". The quad then takes off and does a RTL. Everything...

View Article


Which made the mini heli crash

@talos wrote: I am using 3.4 to flying a mini heli, when I switch from stabilize to poshold a little suddenly, it just flied to earth vertically. Could some tell me what may cause this problem?...

View Article

Image may be NSFW.
Clik here to view.

NOVAerial Robotics AC3.4-Heli Review and Issues List

@Rob_Lefebvre wrote: I wanted to open a new topic to announce that I am beginning to work with AC3.4 for TradHeli finally. I am reviewing the code, and will be posting my findings and updates here. As...

View Article

Image may be NSFW.
Clik here to view.

Desired Altitude adjustments observed in data logs

@jfield wrote: Hi guys, 3DR pixhawk running 3.4.3rc1 I've been seeing something in our logs that's more obvious as we push the flight times up. We put the multirotor in guided and send it to a...

View Article

Offsets for GPS and IMU

@ultrafuge wrote: @mackay9 Hi Randy, On DJI systems like A2 or A3 you have to set X,Y,Z relative to the CoG for the GPS and the IMU. Shouldn't we have this as well ? Posts: 2 Participants: 2 Read full...

View Article


Unknown error tones, burned pixhawk for no reason

@ITman496 wrote: I am diagnosing a friend's drone. It appears very dead, but we are trying to identify why. They said they had powered it up at one point to just check that everything was working. It...

View Article

Spray drone tank empty alert arducopter

@Sivashankaruav wrote: The pesticides storage tank in spraying drone need indignation on low tank volume. I have digital water sensor which is been places to the bottom of the tank, It will change the...

View Article


Image may be NSFW.
Clik here to view.

Heading function to replace compass

@Sivashankaruav wrote: Hi all, Resent days RTK becoming Very popular and I came across some function called Heading to True North.The RTK module is enabled with two antenna facing in the same...

View Article

UART Disabled output in certain functions

@havi0019 wrote: Hello, I am have been using hal.uartD with a ftdi to send data to external computer for year or two. I did all my uart calls in userCode which has worked with success over different...

View Article


Clone boards and settings in MP

@Adam_Campbell wrote: Got my board 2.8 from amazon 80.00 with compass,power module and 433mhz set. When loading 3 questions Linux? Been saying yesThen is this 2+ ? Been saying yesIn the configuration...

View Article

Hexa unstable take off

@SokratisK wrote: Hello guys, i have a stability problem with my hexacopter...the frame is Gryphon dynamics GD6 and i use APM 2.8i have tried the newest version firmware at first and when i had this...

View Article

Image may be NSFW.
Clik here to view.

APM Clone Power Module. Can this work?

@Jimmy_Oliver wrote: Does this unit work with Pixhawk? Can the wires be rearranged? Should I just get another unit? Posts: 4 Participants: 3 Read full topic

View Article
Browsing all 21347 articles
Browse latest View live