Suggestions how to setup Pixhawk + FBL-system
@ultrafuge wrote: Here are some suggestions how to setup Pixhawk to work with FBL-systems like VBar, Microbeast, GT5.2, etc. Arducopter Heli Version 3.3.3 Tip: calibration of accelerometer is much...
View ArticleFlight Modes Radiolink AT10 don't match Mission Planner
@Adam_Campbell wrote: Flight Modes on Remote 3 X 2 switch 6 mode Radiolink AT10 Remote Dont match Mission Planner. Ardupilot FC Tarot 690 PRO, 750kv Hexacopter X configuration. I originally programmed...
View ArticlePixhawk 2 Shipped with bad safety switch twice
@Kevin_Lunn wrote: Hi all Video link you can see with your own eyes the board not booting up. I found out why the board would not boot the safety switch was wired wrong again and shorted out the led...
View ArticleFailed to upload home location (1)
@jverbeke wrote: Hi, I'm using a companion computer to send velocity commands over Mavlink to ArduCopter (modified 3.4 version) running on PixHawk through FTDI-USB cable. This works quite well. But...
View ArticleCopter 3.4.2 quadcopter suddenly moved on poshold
@philip325 wrote: Quadcopter suddenly moved after about 6 minutes on poshold, this happened a few times on poshold mode. Look like not GPS glitch. Posts: 5 Participants: 3 Read full topic
View ArticleHow to tune the FILT parameter?
@lorbass wrote: Since some releases, in Missionplanner Configuration the new Parameter FILT is available.I can't find a wiki what this parameter does nor how to tune it. And I don't dare to change it...
View ArticlePitch autotune messing with roll parameters
@4sfaloth wrote: I believe I may have stumbled upon a bug concerning the autotune. I have just performed an autotune for the pitch axis only, and the aircraft performed it successfully. However, I...
View ArticleUpgrading Iris+ Transmitter
@marcovnu wrote: I am interested in upgrading my transmitter on the Iris+ and decided on either the Turnigy 9xr Pro or the Taranis x9d plus. Any recommendations? Also, I am still a beginner. How...
View ArticleWhat swashplate option does ardupilot currently have?
@reaper64D wrote: I am looking to see if ardupilot would be a good system for me to use on a few projects i am working on.I was looking through the online manual found on the site and it was very...
View ArticleApm 3.4.1 mini helicopter poshold mode
@talos wrote: I flied a mini helicopter using firmware apm 3.4.1 under mode poshold, when I flied heli from one place to another, it did not stay at the destination play immediately but vibrated two...
View ArticleClik here to view.
L3GD20 Failed！！！
@jane wrote: I connected mpu9250 on external SPI port of Pixhawk, then L3GD20 failed. The firmware I used is copter-3.42. Anybody know about it? I will be appreciate if someone can help me. Posts: 1...
View ArticlePixHawk 2.4.8 Arming Sequence
@pmshop wrote: After loading 3.4.2 (and now 3.4.3-rc1) the PixHawk LED main indicator no longer flashes while arming. Posts: 1 Participants: 1 Read full topic
View ArticleMeaning of IMAX in attitude controller
@mahesh_saraswat wrote: Hi,I am trying to tune PID's in my quadcopter. In mission planner/config/tuning section there under the throttle accel section IMAX value is 80. I want to know what does this...
View ArticleQuantum Nova Not a Good Buy
@Cecil_Frank wrote: I have a Nova quad , The green light has no power to it from the gps , is there anyway of buying similar one then spending a 70 to 80 dollars on one. I also found the motors donot...
View ArticleClik here to view.
If there such big NEKF4 SV, what would happen?
@talos wrote: When I flied the mini heli using APM 3.4, it suddenly landed. I checked logs, found that SV was almost 10. Did this cause the crash?Thanks! Posts: 1 Participants: 1 Read full topic
View ArticleWierd yaw issue Newly setup quad
@jtroutt19 wrote: Hey guys I recently switched from librepilot to Ardupilot. I am running a pixhawk with 3.4.2 on it. I got it all set up and ready to the other day. Sat down with it tonight in the...
View ArticleHow to run the examples,I have stuck on this for ten days!
@dzy6489 wrote: Hello I was trying to follow the steps on the website below http://ardupilot.org/dev/docs/learning-ardupilot-the-example-sketches.html69 However i am facing with the below line on the...
View ArticleThere is no serial data when run the examples
@dzy6489 wrote: I follow the tutorial http://ardupilot.org/dev/docs/learning-ardupilot-the-example-sketches.html#learning-ardupilot-the-example-sketchesThe examples/INS_generic can be build and...
View ArticleQuestion of GPS configuration in 3.4.3? (Refresh rate)
@ghostsharp wrote: Hi, I have GPS Ublox M8n, and i want to know if is possible configure rate to 10Hz (maximun possible) instead of 5Hz that configure automatically firmware? Posts: 2 Participants: 2...
View ArticleBad logging error
@HarrisAerial wrote: Getting a bad logging error as soon as I arm copter.. issue started occurring after installing sf11c range finder.. could it be an issue with the SD card or something else? Posts:...
View Article