Does arducopter support a pitot tube?
@robertrotzetter wrote: pretty straight foreword in the title. Posts: 3 Participants: 2 Read full topic
View ArticleCompatibility of dronekit python with Ardupilot APM mega
@arpit_srivastava wrote: Can i run dronekit python codes with ardupilot apm mega? Posts: 1 Participants: 1 Read full topic
View ArticleI can't get my unit up!
@Jerry wrote: My Skyviper can't get it up. After having flown the unit successfully for a few weeks including fully automated Mission Planner missions, I had some problems that required taking it back...
View ArticleControlling Copter via mavlink
@sergi_torrabadella wrote: Hi everyone! I'm involved in a project in which I would need to control the throttle, roll, pitch and yaw of the copter depending some sensor samples. I've tried to generate...
View ArticleInteresting log: Hexa motor failure, undetected "crash" and a dizzy EKF2
@Thorsten wrote: Hi all, at thorstenbehrens.de/HexMotorFailure_U.zip you find a log from a colleague of mine. During an auto mission one motor stopped working. The reason must be a mechanical or some...
View ArticleCopter Loiters for 50-60 seconds instead 5 seconds Delay in AUTO?
@R_Q_Robert wrote: Hi All Previously i was using AC 3.5.2 on my Quadcopter with Pixhawk 1GPS ublox M8NTaranis X9E But i deliver the quadcopter to my customer with AC 3.5.4 .No Telemetry rewquired just...
View ArticleKDE ESC + KDE MOTORS + Pixhawk 2.1 with APM 3.5.3 help needed
@Ced_Bonero wrote: Hello, I'm new on the community. We've bought several cube and KDE ESC (UAS55) togetether with KDE (4014XF 380Kv and also 4012XF 400Kv) motors and they are mounted on a X8...
View ArticleAPM Planner Horizon 45gr after connect LED Lights
@fulco_heusdens wrote: When I level veloc. in setup. Then connect the led light on the ports 5,7 and beeper on 6.The horizon in APM planner is on turns 45deg ccw and the drones stands level.The veloc...
View ArticleAssistance w/ Interpreting Logs
@franklin_m wrote: I've looked through this pagehttp://ardupilot.org/copter/docs/common-downloading-and-analyzing-data-logs-in-mission-planner.html#manually-review-a-log But there's still entries that...
View ArticleInner workings of optical flow based position hold
@MCITYFC wrote: Hello I'm setting up a system where an on-board computer (in this case, Intel Aero Compute Board) is flying a pixhawk. I'm trying to implement position hold using optical sensors in a...
View ArticleRTL after landing in the middle of a mission
@Nick wrote: Hello,I just have a question RTL mode and Land mode. Say I start a mission in auto mode, and halfway between two way points I take back control of the copter, land it, and disarm it. If I...
View ArticleCopter-3.5.5-rc1 available for beta testing
@rmackay9 wrote: Copter-3.5.5-rc1 is available for beta testing. This is a relatively minor change compared with 3.5.4 (Release Notes) ICM20948 compass orientation fix LIS3MDL compass support on...
View ArticlePixhawk does not recognise NMEA input (Edit:Solved)
@luke_e_h wrote: Hi everyone, I am attempting to input an NMEA signal into a Pixhawk running Copter 3.5.4 but I'm having trouble getting the Pixhawk to recognise the signal.(I know NMEA should not be...
View ArticleClik here to view.
Quad Flip at takeoff
@Suopo wrote: Hi All, I'm a newbie here, this is my 1st post.and of course looking for help I replaced the original DJI FC in my old F450 with CUAV Pixhack v3.Setup went well, Accel calibration, GPS...
View ArticleNo take off log help
@edge540T wrote: Vibes are high, isn't it?but I'm missing something big that I can't find, it's a tarot 650 and pixhawk 2 which don't want take off without crashing. I have uploaded one in stab which...
View ArticleHow to Arm Sky Viper Gps In Auto Mode
@Doug_Kampen wrote: Need some help here, I created a flight plan via mission planner, uploaded to the drone, but having issues arming while in auto mode. I have the flight mode set to auto, but cannot...
View ArticleClik here to view.
Compass Calibrate Offsets are a bit differrent from Matlab result
@RizHuang wrote: Here are result which worked out from APM CompassCalibrare.cpp PARM, 8048398, COMPASS_OFS_X, 28.60939PARM, 8048423, COMPASS_OFS_Y, -82.79034PARM, 8048626, COMPASS_OFS_Z, 130.0766...
View ArticleAUTO (waypoints) mode: is it possible to change speed in flight?
@Steve79 wrote: Hi all, i have a question: is it possible to change speed while flying in AUTO mode, like having it on a pot of the TX so it can be changed in real time? something it would act like a...
View ArticleSerial0 vs Serial1 speeds
@re4mat0r wrote: Hi. Serial1 transfer speed is much slower than Serial0 on my PX2.1. I use APM Copter 3.5 and tried many different settings, no matter what I can not download dataflash logs via...
View ArticleOwn PID Values in Mission Planner
@PhoenAix wrote: Hello, for education i built a quadrocopter. Now i have written a simulation for calculating the best PID Values and want to put these values in Mission...
View Article