Reverse waypoint and reverse track rtl
@Ben_Schreurs wrote: Hi my job is creating custom drone's. i get the question a lot for reversing a waypiont track and for a rtl or go home funtion with reverse track. Is this posseble. Posts: 2...
View ArticleClik here to view.
ArduCopter BLDC No Response
@rijun034 wrote: I have completed all calibrations including ESC & Flight Mode configured. Tried with both options Arm-Check Enabled and Disable. In mission planner, it's showing that ARMED. But...
View ArticleMAVLink in SITL
@Drony wrote: Hello, I added new functions to AP_Mission that allow adding/removing a waypoint while a mission has already started. Using the scheduler I already tested them to some degree and they...
View ArticlePixracer with minimosd micro No data!
@chris661 wrote: After doing some configuration with telemetry (frsky) everything is ok, except I've got a No Data displayed in my goggles. I've the latest firmware (3.5.4) .I connected my telemetry2...
View ArticleHere GNSS built-in Compass change issues and bettery voltage Question
@Mr.lee wrote: robotshop.com hx4-06022_change_notice.pdf 102.85 KB Gps set up Question. Mission planner -> INITAL SETUP -> compass-> compass #1 pitch 180 yaw 90 set up it that right? or how...
View ArticleSkyViper and Tiny GPS RTK
@colorsound wrote: Hello Guys, We are trying to do some swarming GCS and skyviper is perfect for fun and testing with it. I need to do some sort of quick test to determine how good the position...
View ArticleBuzzer settings
@Charles_Brooks wrote: Any way I can change it so the buzzer will go off with less then half the pack left. Posts: 1 Participants: 1 Read full topic
View ArticleUpdating fermware
@Charles_Brooks wrote: So I'm still learning the ropes. When I update firmware will it keep my settings or do I have to redo all the radio, compass and other calibrations? Posts: 1 Participants: 1...
View ArticleObstacle avoidance with TF mini
@nicodh wrote: Hello, i'm playing with the benewake TF mini lidar trying to use it as a front proximity sensor. I have managed to read correct values in sonar range after upgrading the TF mini...
View ArticleAsk about ardupilot that does not work after calibration
@Ahmad_Jalal wrote: why after I calibrate, my arducopter is not working. I use APM.2.0 software.thanks. Posts: 2 Participants: 2 Read full topic
View ArticleSuggestion: Parameter to switch off WiFi before take off
@Thorsten wrote: Hi all, on the Pixracer the Wifi board is located pretty close to other components - especially one small drones the Pixracer was desiged for. To reduce any problematic interfence it...
View ArticleThe copter is touching the gorund with throttle stick down by 1 level
@Aritra_ghosal wrote: 47 01-01-1970 05-30-00.bin (973.5 KB) What happens is while on height of 13 14 feet....i just throttel down to 1 level and its comes down and touchs the ground and goes up again....
View ArticleApm mini 3.1 Can not set logging on
@john wrote: The quad flies pretty well, but I have problems with motor 4. It will not start like the other three even though I calibrated several times and even switched out with another esc and...
View ArticleGetting transformation (6D) between two frames
@HumamHelfawiOptecks wrote: Hi,Depending only on the IMU (No GPS or other sensors), I want to get transformation that happened between two frames (two moments) which includes YAW, PITCH, ROLL, X, Y,...
View ArticleAnother Bricked Transmitter
@lordneeko wrote: This is now the third person (including myself) whose transmitter was bricked after a firmware update. https://www.rcgroups.com/forums/showpost.php?p=39004849&postcount=136 Can...
View ArticleStick Mixing/manual obstacle avoidance in Auto mode
@Simone_Azzalin wrote: Has anyone successfully implemented stick mixing in AUTO mode? I come from the Arduplane side of ardupilot and love the fact that you can adjust the position of the aircraft in...
View ArticleOverride sitl IMU values with externally simulated IMu values
@jakkala_kalvik wrote: Hi, I am working on my own simulator for the sitl and I am not sure how to send my simulated IMU values to the sitl. I am doing it so that when my drone in the sim collides with...
View ArticleMotor spins at zero throttle even at -50 Trim in RC
@rijun034 wrote: I have calibrated ESCs and the Quad 'X' working perfectly. When I connect the battery when the throttle is high, pixhawk again goes to ESC calibration mode and restarted the pixhawk....
View ArticleRestarts When Connecting with MAVProxy
@Mustafa_Gokce wrote: Hi.I am trying to connect using mavproxy.py in linux to the ardupilot mega board.When i connect to the board with usb cable it immediately reboots.How can i disable this reboot...
View ArticleNeed more telemetry output on Pixhawk
@lawfx wrote: I have a BIG problem and little experience (not enought) with Pixhawk ports. I need to install MiniOSD, 3DR clone telemetry and Mavlink Led Controller, but they need Telemetry ports, and...
View Article