About the APM official website video
@xiaoxilang wrote: why a lot of APM official website video can not watch?Do we need the special ways and methods to get and watch? Posts: 3 Participants: 3 Read full topic
View ArticleCopter did TAKEOFF in stabilize mode through a mission command
@Andreas_Krauchi wrote: I have a companion computer connected to my copter which does upload and start the mission (the mission icludes a TAKEOFF event and at the end a LAND command).The upload to the...
View ArticleNeed Complete Setup Guide for a APM 2.6 Helicopter Ver 3.2.1
@rfine7666 wrote: Thanks in advance for any helpI have recieved a lot of good help and tips from this forum and it's users, Thank You.I have viewed and read a lot of comments and tips for correcting...
View ArticleFlight Mode can't changed by MAVLINK via Python (pymavlink)
@Svenno wrote: Hello, i want to change the Flight Mode via Python (pymavlink) and a companion pc, but it doesn't working.ArduCopter 3.5.2 with Pixhawk and the latest pymavlink library on the Raspberry...
View ArticleWill RTL respond to a dynamically changing Rally Point?
@rrr6399 wrote: I just discovered the newish capability of RTL flying to the nearest Rally Point and the Moving Base capability of Mission Planner. Its my understanding that RTL will fly to the...
View ArticleClik here to view.
Using lidarligth laser rangefinder to ensure fixed horizontal distance during...
@fundus wrote: Hellolooking into getting a LW20 sensor and have some questions if anyone can help clarify. User case 1: During inspection/mapping of a vertical surface like a dam or the fasade af an...
View ArticleYaw delay on Pixhawk PX4
@Carlos_FPV wrote: Hi everyone, I just finished building my tarot x6 and I have a big delay on the response of the yaw, but there's no delay on pitch and roll. Any idea of how to fix it? The setup...
View ArticleSet stream rate for a specific message
@jasonbeach wrote: Is it possible to set the stream rate for a specific mavlink message? i.e. I would like to send the attitude message to a companion computer faster than 10 Hz. Is that possible?...
View ArticleCopter 3.5.2 Compass Drift
@jarife wrote: Hi, Recently updated the Copter Firmware from 3.5.1 to 3.5.2. This is being flown on an S1000 octocopter frame, Pixhawk 2, and laser altimeter. After successful calibration of compass,...
View ArticleRecommended Motors, Props & ESCs for TAROT 680PRO Build + PIXHAWK 2.1
@radioflyer1985 wrote: Hi, I need some ideas on recommended Motors Props & ESCs. I was looking at the DJI e800 kit. Is it worth it? Does it work well with the PIXHAWK 2.1. I would love to hear...
View ArticleEKF wiki clerafications
@Raviv wrote: HiI was going through the EKF wiki and need help.On the Commonly modified parameters it says: EK2_ALT_SOURCE which sensor to use as the primary altitude source 0 : use barometer...
View ArticleMissing custom mavlink message at ground station
@subhashkrishnan wrote: I have added a new mavlink message in common.xml within Ardupilot. The new set of headers are made available to QGroundControl as well as Ardupilot. When Ardupilot is executed...
View ArticleCan never view or download parameter file or tuning file?
@rfine7666 wrote: Thanks again for any helpI have read quite a few topic files where people are asking for a 450 parameter or tuning file to use as a aid for a setup. I have read where some of these...
View ArticleRC9_function missing. How to use the AUX?
@whakahere wrote: I have two copters that I wired up the same and one I have the camera switch working on rc8 by using rc8_function = 1 On my other copter which has 3.5.1 I have more channels so...
View ArticleMission Planner with Copter 3.5.8 showing Bad Logging
@awfp wrote: Hi! After letting my quad stand on the shelf for some months after a crash I wanted to get flying again.But after loading the latest FW and setting everything up I couldn't arm it since...
View ArticleArduCopter ignoring my region of interest?
@larsks wrote: I'm using Copter 3.5.1. This is an auto mission I tried flying this morning (exported via wp list in mavproxy). QGC WPL 110 0 0 0 16 0.000000 0.000000 0.000000 0.000000 43.371098...
View ArticleIt shoots straight up when I switch to PosHold
@Dimitris76 wrote: I just put together a new camera quad. It's the 3DR DIY frame with a Pixhawk running 3.5.2 and Ublox M8N GPS.I have rock solid GPS reception (# of sats and low HDOP), calibrated...
View ArticleCopter Falls From Sky after Mission Start Action Excuted
@Michael_Letterio wrote: Hello all, I have been recently attempting to enable an autonomous mission. I have tried multiple times using the auto mode using my controller with no success. I then...
View ArticleH-frame takes the long way to yaw (bug)
@Iketh wrote: Any automated flying, the copter turns in the wrong direction (takes the long way around). I also had to inverse that channel in Taranis. However, it successfully maintains a heading...
View ArticleMotors on quad slows down wery slowly
@lospalos wrote: Guys I need help. when in stab mode, motors follows RC throtle stick OK but only when rising it. When want to slow them down (e.g. want to descent) they loose rotation very slowly. It...
View Article