Err.flight_mode-16?
@Doolly wrote: I am testing loiter mode with optical flow and after getting in to loiter about 10s with a little flow my copter altitude oscillates and doesn't get my RC command and throttle keeps go...
View ArticleSlowly reaction
@Petr wrote: Please, help my with my new Copter. I used APM2.8 on F450 frame.I have one problem with slow reaction copter to left / right tilt (UP/DN reaction is OK). After the arming is this reaction...
View ArticleClik here to view.
Terrain Following : Works in Auto, but not in Guided?
@Chris42 wrote: Hi, After seeing this excellent video of Randy (thanks! ): With my Pixhawk under AC.3.4.5 and my EZ4 Maxbotix, I tried to do the same thing and did a terrain-following test that works...
View ArticleTesting 3.5-RC1 on my Solo - She flies!
@Pedals2Paddles wrote: Today I decided to become a test pilot and/or crash test dummy, depending on how you look at it. Since I don't have a DIY bird up and running to use with 3.5, I decided to see...
View ArticleBattery madness
@Adam_Campbell wrote: I have a Tarot 690, 750kv hex with m8n, ardupilot 2.8apm. Running 3s 8000 mah Floureon bats. The thing is set in Mission planner to go into RTL at 10.2 but is RTL landing at 11.7...
View ArticleUnusual swashplate behavior using AC 3.4.5 in ACRO with full cyclic input
@bnsgeyer wrote: I'm looking for some assurance that this behavior is considered normal or the result of a poorly designed test for trad heli community. I loaded AC 3.4.5 from mission planner to my...
View ArticleThrottle problem
@kombatunit wrote: When I arm my pixhawk, my motors spin pretty fast maybe 20-25% of max with throttle stick at minimum. I'm running ardu copter 3.4.5 and my TX is a taranis. I've read that I need to...
View ArticleOptical Flow - Step by Step
@Hadi_Ahrovani wrote: This topic created for share and intro to OF. thanks for share more info about configuration and coding and so.. Posts: 1 Participants: 1 Read full topic
View ArticleAc.3.4.5 - Y6b - help please
@netptl39 wrote: Hi everyone!Is there any known issue with subject config? I just had 2 brand new Y6 builds hit the ground the exact same way. Both boards flew great in X4 config a month ago but now...
View ArticleAyuda por favor
@walternino wrote: instalo mission planner pero cuando voy a las acciones no me aparece todas ventanas ya desistale y lo volvi a configurar y nada ..sera posible que me puedan ayudar Posts: 1...
View ArticleClik here to view.
Almost fly away during hover test
@Bennet wrote: Today I did my third small hover test with my (first) 250 build. All was ok until about 5 min then the copter suddently increased throttle (not to max, I guess it just got stuck in the...
View ArticleSingle Rotor Drone using Pixhawk/Arducopter
@ali_imran wrote: Hello, I am trying to make a single rotor drone using pixhawk/arducopter. the problem is, as you all know, there is no builtin firmware for it. What should I do? How and where should...
View ArticleSingle & CoaxCopters with AC3.5
@rmackay9 wrote: Copter-3.5 (in beta testing at the time of this post) includes the Single Copter and Coax Copters in the main multicopter firmware. This means if you load up the AC3.5-rc1 (or later)...
View ArticleLidarLite3 doesn't work on pixhawk?
@zhitao wrote: Hi,all I experienced an odd issue. I install a LidarLite3 rangefinder on pixhawk on my copter, when I fly it in manual mode, the LidarLite can work, I put something below the copter, it...
View ArticleV3.4.5 - Motor #4 Anomaly: Fails to spin up when armed
@ENG6266 wrote: I have a little conundrum with my Pixhack v2.81.... (this is a testbed for learning and experimenting with ArduPilot based systems... Pixhawk 2 will be on it's way shortly after...
View ArticleClik here to view.
RTK GPS for Multicopter
@ferocity02 wrote: Hello, I'm putting together an S1000 with a Pixhawk 1 and would like to add RTK GPS to the system for enhanced location accuracy. The Emlid Reach kit seems like it integrates easily...
View ArticleCopter-3.5.0-rc2 has been released for beta testing
@rmackay9 wrote: Copter-3.5.0-rc2 (2nd release candidate) is now available for beta testing. As per usual the beta version can be downloaded using the MP's Install Screen's beta firmwares link and I...
View ArticleSetting up RSSI with pixhawk, minim OSD, and EZ UHF
@Ktrpilot wrote: Hi all If there is a grand wizard out there who might be able to help It'd be greatly appreciated. I've run into a few issues trying to set up a minim OSD running Night Ghost firmware...
View ArticleThe differences between airspeed and groundspeed?
@zhitao wrote: Hi, all I view the dronekit document, there are airspeed and groundspeed parameters, I use a mutilcopter, so I am confused, what's the difference between them? Thanks a lot in advanced...
View ArticleHow to enable EKF on older version of APM
@cwzerr wrote: Hey, I'm trying to figure out how to enable the EKF on our older version APM board. I've read that I need to enable the AHRS_EKF_USE parameter to '1', but I do not have that parameter...
View Article