Does Solo run on copter-3.4?
@lroberts wrote: I uploaded copter-3.5 to my solo, but I cannot currently arm solo. Perhaps there are compatibility issues with solo and 3.5 that still need to be worked out. Is it known whether...
View ArticleQuad drops when yawing in alt or loiter mode
@Z9G6 wrote: Hey all! Trying to diagnose an issue here. here is the logs. 2017-02-17 13-56-45.bin (193.9 KB)2017-02-17 13-56-45.log (479.9 KB) the Quad is a 500 sized frame with a mini APM running...
View ArticleFirmware version and I2C voltage - APM 2.6
@ph00ns wrote: Hi, I have a APM 2.6 FC that is behaving unexpectedly. I can load the latest firmware (AC3.2.1) but it will not boot (i get the error AP_Baro_MS5611 did not initialize for 1000ms)....
View ArticleGasoline Helicopter Configuration
@Mustafa_Efe_Cetin wrote: Hi, I want to fit my pixhawk to a gasoline powered heli. Could you give me suggestion for configuration? Is it possible to fit or reliable to operate. Posts: 1 Participants:...
View ArticleMoving from 3.3.3 to 3.4.5
@cookmangr wrote: I have a hexa that i have fly perfectly for a year with 3.3.3 but know i m modified it to a coaxial X8 and i install the firmware 3.4.5Is there something that is a very big change in...
View ArticleHow to install firmware on APM 2.8
@sergi_torrabadella wrote: Hi everybody, I'm planning to start a new project with Ardupilot (Copter) but I'm really new and I'm a little bit lost. I've recently bought an APM 2.8 board on Amazon....
View ArticleInterchange F450 Battery between 3S and 4S
@dasun wrote: Hi, Currently, I am using a 3S battery with my F450 pixhawk quadcopter running with ardupilot 3.4. The problem I have is the flight time is very less around 5-7 mins. So I am going to...
View ArticleControlling led's on a pixhawk quadcopter
@alan3113 wrote: Im new here and not sure where to start.But im trying to turn led's on and off with a switch on my TX .Im not having much luck.Im using a Pixhawk flight controller if it was an apm...
View ArticleCopter 3.4+ update, Transmitter calibration issues
@Biswajit1995 wrote: I am facing a weird issue while upgrading my pixhawk firmware to v3.3.3 to v3.4.4, in Radio Calibration, there are no green bars showing to calibrate my transmitter sticks, even...
View ArticleClik here to view.
Voltage on board with power module only 4V whats wrong?
@shyriu42 wrote: hi i m new in this forum and i buy an apm 2.8 with his power module. All was ok until i disconnect usb and i connect the battery. My RC receiver is on alarm because my RC receiver...
View ArticleCopter V3.5 Rc1 Loaded Onto AUAV-X2.1 Flight Controller - Quad Flight
@Jon22 wrote: Not sure whether V3.5 Rc1 release covers the AUAV-X2.1.Loaded Copter V3.5 Rc1 onto my AUAV-X2.1 flight controller via Mission Planner. Noticed in the HUD, pitch appeared as roll and vice...
View ArticleModule SSD1306 Not working on Pixhawk 2.1
@mfbs17 wrote: Module SSd1306 not working on Pixhawk 2.1 but works fine on pixhawk. Posts: 3 Participants: 2 Read full topic
View ArticleAPM 2.6 Compass change - beeping
@jero wrote: Hello everyone,I have one issue with my 2.6 board.I figured out that my external compas is not ok, so Iswitched to the one I have on GPS module.I connected SCA and SCL to I2C port.I...
View ArticlePoshold did not work with 3.5.1
@iseries wrote: Using Pixracer with 3.5.1 and a 250 quad copter3DR GPS Took off in stabilize mode and then switch to Position Hold mode. Copter drifted in the wind in one direction.Reposition the...
View ArticleCopter 3.5-RC1 Compass not calibrated error
@Rusty_Jones wrote: Copter 3.5-RC1 on a Pixhawk 2.4.8.Fresh install, calibrated compasses indoors, ok not best idea, but it did calibrate in Mission Planner. Go to trim it and Autotune it today, and...
View ArticleClik here to view.
Modifying Ardupilot 3.2.1 's code
@spirit wrote: I'm from korea and I'm interested in programming my own code(it is just my hobby but I'm studying hard these days) and I'm really really respect and admire people who are concerned in...
View ArticleInverted flight in Arducopter?
@josealb wrote: I am planning on installing DJI Z430 ESCs on an arducopter based quad and just saw that they allow to switch the direction of rotation, thus allowing for inverted flight. I didn't see...
View ArticleClik here to view.
Aircraft Size, relative angle to magnetic North
@ACPUK wrote: Interesting question for you clever people.Should there be a ratio of external compass height to frame size. As in assuming a Carbon Fibber frame the larger the body the higher the...
View ArticleMaking poshold braking more aggressive?
@larsks wrote: Is it possible to make make braking when in POSHOLD mode more aggressive? There is an old GitHub issue on this topic that suggests the existing tuning values (PHLD_BRAKE_ANGLE and...
View ArticlePixhawk and underslung gimbals
@timbaconheli wrote: Hello, So im gearing up to build a system using Pixhawk 2. The base frame is comprised of Trex 700 mechanics with a standard style head, not DFC. It has been stretched to 800mm...
View Article