About debugging the arducopter firmware on windows in eclipse IDE
@nithinsreddy wrote: Hi, i am trying to build the adrucopter for pixhawk firmware,its building and generating adrucopter.px4, px4io-v2.elf and px4io-v2.bin files. when i debug the code, it is running...
View ArticleClik here to view.
I have some questions to the AUTO missions with pixhawk
@aamadeuss wrote: Hi, i have some questions to the AUTO missions with pixhawk copter:usualy i upload my mission, arm, take off in stabilize than switch auto and wait until the copter does RTL and fine...
View ArticleHow to control Copter for alternative follow me mode
@josealb wrote: I am creating an alternative follow me mode using a companion computer on board the Solo. The drone must be able to point the camera and follow the subject.What do you think is the...
View ArticleBattery trade offs mah vs weight of multiples
@Adam_Campbell wrote: I purchased a 3S 5500mah 40c lipo for my Tarot 690 hexacopter with 750kv xinte 5010s , I get 12 minutes give or take. I have just ordered a parallel cable and Two 3S 8000 mah 45c...
View ArticleuBlox 8 on newest APM 2.8 BOARD Running copter 3.41
@Adam_Campbell wrote: I have the neo 8 ublox Radiolink SE100 on my ardupilot 2.8 I just installed. Are there any steps I need to take to insure im getting any benefits over uBlox neo6.? 2nd question I...
View Article3.4 on 3dr Solo - help
@dabuek wrote: Hello, are there any instruction available that can help install AC3.4 on SOLO? Posts: 1 Participants: 1 Read full topic
View ArticleSimpleBGC Alexmos 2.4b6 gimbal control from Pixhawk PX4 serial to UART
@onthelearningcurve wrote: Looking at the Ardupilot wiki for gimbal control, I see that the SToRM32 gimbal can be controlled from the Pixhawk PX4 serial port to the gimbal UART. The SimpleBGC 2.4b6...
View ArticleGPS_GNSS_MODE and the best configuration
@pauljatherton wrote: Just looking into this parameter trying to understand why in my 4 ardupiloted craft that they all behave differently when it comes to the responsiveness of the GPS - for which...
View ArticleSupport for 16 channels?
@wicked1 wrote: Would it be possible to support 16 PPM channels?Is anyone else interested in it?Could the extra two be passed through to unused motor ports?Even the ability to assign 1-10 to internal...
View ArticleProblem with throttle out Copter 3.4.2
@Niels wrote: Hi everybody, not really sure if i'm doing it right. Building my third copter now and i'm standing in front of a problem i never experienced. As in the attached log i experience some...
View ArticleSafety switch only for motors
@Kudykam wrote: Hi, Is it possible to activate safety switch to block only motors, but no AUX 1-6? So I can control my LEDs and servos without pushing safety switch? Posts: 11 Participants: 3 Read...
View ArticleClik here to view.
RCHeli T-Rex500 ArduPilot AC3.4.2FW Maiden Flight
@zhangsir wrote: Today on my T-Rex500 helicopter, daring to test the latest version AC3.4.2 firmware. Initial feeling very good, use default parameters for basic stabilization of flight, aircraft...
View ArticleM8n config file in wiki corrupt
@pauljatherton wrote: TheMarco M8N config file linked on this wiki page (http://ardupilot.org/copter/docs/common-ublox-gps.html) causes u-center to crash right at the end of applying the config. I...
View ArticleClik here to view.
Technique to expand Roll and Pitch Rate PID gains without instabilities
@bnsgeyer wrote: I am writing this discussion topic illustrate how I used the filter to successfully reduce the instability to increase the P and D gains. I’ve read in the Copter traditional...
View ArticleHardly no throttle
@Cecil_Frank wrote: I have a Quantum Nova and went throw Mission Planner Wizard After all this I found the quad willnot work on motor test in Mission Planner. and works on calburating tranmitter ....
View ArticleFly the Arducopter APM 2.6 autonomously
@Vikrant_Fernandes wrote: I am new to this discussion forum so please bear with me. I have a arducopter apm 2.6 flight controller. It works fine with mission planner and the fly sky RC kit. I am...
View ArticlePost-landing flip with 3.4.2-rc2
@HITMAnsOFT wrote: Hi, I've just completed a new TBS Discovery Pro build and went for first flight and autotune session. The flight was clean from takeoff, roll autotune has completed, then I switched...
View ArticleClik here to view.
AC3.4.2 firmware version Loiter mode aileron operation problems
@zhangsir wrote: Hi @tridge @rmackay9 In yesterday's first test T-Rex500 AC3.4.2 version of the helicopter firmware, Loiter mode to the left aileron, the aircraft did not move to the left response,...
View ArticleHaving 2 different loiter modes
@HarrisAerial wrote: Hi guys, I'm curious as to whether anyone has ever set up 2 different loiter modes, with varying control speeds? My question arises due to the nature of my clients' spraying...
View ArticleThrottle IMAX increasing by itself after flight
@HarrisAerial wrote: I've been having an issue with the new beta on both PH1 /and PH2 where my throttle IMAX is increasing itself after a flight.. it isn't noticeable in flght until the IMAX gets to...
View Article