Clik here to view.
Autotune problem of DJI S900 frame
@oscar0613 wrote: Hi everyone, I'm a beginner, I have some questions of autotune, hope you can help me to figure out, I'll appreciate with your kindly help. The following is my equipment:Aircraft...
View ArticleBest way to control jaw using MavLink?
@KarlU wrote: What is the best way to manipulate jaw of a quad using GCS via keyboard key presses? I do this currently via PID algorithm on GCS and rcoverrides. Is there a way to control jaw...
View ArticleClik here to view.
Bad Motor Output with APM!
@Antoine wrote: Hello everybody, After struggling with taking of for about 2 weeks, I think that I finally found out that my APM card makes BAD outputs for the motors. In fact, when I look at the logs...
View ArticleAUTO terrain following
@chwieser wrote: I would like to make LIDAR terrain following in AUTO mode working and use APM:Copter V3.4.1 (04c76843)Mission Planner 1.3.41TERRAIN_FOLLOW 1TERRAIN_ENABLE 1 The Status tab...
View ArticleSetting Mid throttle in 3.4. Where is the Mid Throttle Parameter?
@Marc_Dornan wrote: I have powerful quad and I need to set mid-throttle. In 3.4 I can no longer find the Mid Throttle parameter/slider. I am aware of the fact that it is supposed to set this...
View ArticleFutaba R7008sb and 3.4xxx not working
@nathansmsu wrote: I hope this is the correct place to post this, but as soon as I updated from 3.3.3 on my X8 Octo to 3.4 I lost connections with my Futaba R7008sb receiver connected via Sbus. I...
View ArticleTransmitter flight mode for using guided mode on ground station or tablet...
@AlexL wrote: Hello, Still trying to understand automated controls a little better - i did read the wiki page on guided mode. still a little unclear though. I have used AUTO mode to execute a planned...
View ArticleClik here to view.
APM compass live calibration problem
@npatel023 wrote: Hi, I am trying to do a compass calibration and my points are all horizontal.Here is a picture of what is happening.Any help on this would be appreciated, thank you! Posts: 1...
View ArticleFlight Modes besides stabilize copter drops until stabilize selected again
@Adam_Campbell wrote: I have read several posts about motors disarming when other modes are selected. Mine dropped about 150' before I got it to re arm and narrowly escaped a 300' dive towards the...
View Article3.4.1 will not calibrate
@pmshop wrote: On my Quad 3.4.1, everything calibrates fine (except a compass issue of high offset no matter how I calibrate).But on my HEX, 3.4.1 refuses to calibrate the accelerometers. Also noted,...
View ArticleAbout ROS/Gazebo Simulator with SITL?
@Mandeep_Singh wrote: After so many days i started understanding about the whole pipeline and after fixing bugs that came during set up, today i just find out that the page...
View ArticleCopter-3.4.2 released
@rmackay9 wrote: Copter-3.4.2 has been released and can be downloaded from the Mission Planner and other GCSs. Changes from 3.4.1 are listed below: 1) Minor Improvements: ACRO_Y_EXPO applies to all...
View ArticleAPM 2.8 vibration Accz too much and away 0 level
@Pilot2016 wrote: Hi I am working on APM 2.8 and after learning too much atleast its flying and hovering in acro and stablize mode. Now my target is to reduce the vibrations at a level where I can try...
View ArticleAltitude lost and regained in Guided mode, but holds steady in Auto mode
@AlexL wrote: Hello! When I execute a flight plan in Auto, the quad holds altitude nicely as it moves from waypoint to waypoint. When I change the flight mode to guided using the Tower app and command...
View ArticleI'm running 3.4.2 Arming checks
@OAPpilot wrote: HiI can arm my Pixhawk without it doing arming checks, even though they are turned on in Mission Planner. i.e No Sats etc. Is there another param. that needs to be changed? Posts: 4...
View ArticleFly by mavlink topic?
@dpsoul wrote: Hi,I am thinking of using raspberry pi or similar computing platform for maneuvering quad using joypad on the ground.Has anyone done this? Posts: 2 Participants: 2 Read full topic
View ArticleOctoquad with pusher
@CatiaDr wrote: Has anyone here tried using the Quadplane code in an X8 configuration with a pusher motor? We have it working on a Pixhawk with Quad motors but need the extra lift of an X8. Posts: 1...
View ArticleNo logs on pixhawk?
@larsks wrote: I wanted to review the logs on my pixhawk (running APM 3.4.2) after a flight went awry earlier today...but connecting with mavproxy and running log list reveals: STABILIZE> log list...
View ArticleWhere can I buy a Pixhawk Safety (Arming) Switch?
@BigAl wrote: I looked on Amazon and on eBay, but the only ones I can find will take about a month to deliver. Can I buy one from someone in the USA? My switch is broken. Posts: 2 Participants: 2 Read...
View ArticleFly-zones and no-fly zones
@joe535 wrote: Hi, I am just new to this ardu-community and want to set up my own copter next year.I was thinking of the flight-restricion-zones as well.So up to now, the pilot is responsible not to...
View Article