RC7 LeddarOne Rangefinder system fail
@Lance_B wrote: First I guess I should ask if this device has truly been added to the firmware - if not disregard. If it is:Upon testing mine, (set Serial1_Protocol = 9 - Lidar, and Rngfnd_Type = 12,...
View ArticleClik here to view.
Pixracer with RC Helicopter
@zhangsir wrote: @tridge@Rob_Lefebvre understand Pixracer only 1-6 output channel, then, RC helicopter ESC to access 8-channel, how to set it? DSC04948.jpg3200x2133 628 KB Posts: 1 Participants: 1...
View ArticleGPS configuration RC7
@Gregmaan wrote: Hi I am testing with RC7 and get weird messages about the gps configuration:Sometimes the baud rate is 115200 mostly 38400 from messages?Is there a way to get allways the same...
View ArticleCopter spin in LOITER mode (3.4-rc2)
@jyl58 wrote: Hi All : In LOITER mode ,after copter takeoff ,the vehicle start spin,and the yaw stick dos't work .Anyone can help me analyze the flight log? Thanks very much . Firmware :Copter...
View ArticleMapping: too many pictures
@Basti_K wrote: I have been trying for some time unfortunately without result with my Copter to map,but more images are generated as in the log.As an example:135 camera shots and 153 pictures in the...
View Article3.4-rc7 copter arm via mavlink even with RC turned off!
@trancept wrote: Hello, Update this morning from rc6 to rc7 and fly goes well with quad + pixhawk + px4flow + terraranger. What I saw that could be dangerous is that the copter arm via mavlink even...
View ArticleCan't use waypoints with SBF GPS enabled 3.4-rc7 No Terrain Data Error
@mboland wrote: While tracking down a problem causing the Pixhawk to crash I started to focus on the "FS: No Terrain Data" message I was getting every time I selected Auto on the Tx. All parameters...
View ArticleProblems with first build
@Liamb2387 wrote: Hi all. So far so good when building my first f450 quadcopter. I'm using a ardupilot 2.8 with Simonk 30a escs. Everything is fully assembled but I'm having a problem. The quadcopter...
View ArticleCopter-3.4 has been released!
@rmackay9 wrote: As reported on this blog post, Copter-3.4 has been released and is available as the default firmware through all the ground stations. The previous version (AC3.3.3) can still be...
View ArticleFeature Request: ESC (BLHeli) USB Passthrough
@Frontier wrote: Very excited today about the release of AC 3.4 final, will update my rebuilt S500 quadcopter as soon as possible and test.Many thanks to all people making this possible. What I would...
View ArticlePX4Flow module problem?
@wifiguru10 wrote: Got Copter 3.4 on the quad copter (latest). Using a pixracer and PX4flow optical flow + maxbotics sensors. I hook everything up and I configure it but the FC doesn't show any flow...
View ArticleRTL failure, resulting in crash
@netphreak wrote: Hi all, Just had an interesting crash. Flew my large X8 (28in props, 6S) and went to test RTL. It worked well, but when it went into the landing phase, the motors dropped to idle at...
View ArticleAutotune not showing as selected mode
@Flyingstoo wrote: HiI am trying to use the auto tune function for the first time using a pixhawk.I have set up Altitude hold on channel 5 and have set up a switch on channel 7 to initiate Autotune....
View ArticleBattery Autonomy - Time flight
@Claude_Rychter wrote: Dear all, I'm facing an issue and wondering why my Battery (6s 12000mAh) supposed to provide a 35mn flight time just gives 20mn (Out of Battery)... Then, Check voltage after...
View ArticleTemperature monitoring possible?
@X1Aero wrote: Coming into the cold season for work and want to monitor battery temperature. The batteries are kept in a thermostatically controlled case until flight and wrapped in insulation, but as...
View ArticleUse Sticks for Gimbal and Camera While in PosHold
@davidbitton wrote: Is it possible to change the behavior of the sticks while the craft is in PosHold in order to use them to control the gimbal and camera? I thought I might be able to do this with...
View ArticleNew to this and need few advices
@DrVonSinistro wrote: Hi, I have 2 birds. A trex 500 clone and a old Thunder Tiger Raptor 90 that has a 3 blades head (assy blades) and OS GT15HZ motor with EzUHF. On my trex I have a Align APM Lite...
View ArticleTrim Advice - Save trim on channel 6? Adv Params?
@AlexL wrote: Hello, I am about to go out for my second flight, which hopefully wont end in a crash since i replaced an esc! I have an APM 2.6 and a 6 channel remote. To start with, since I suck at...
View ArticleYaw issues using indoor GPS navigation
@shinig4mi wrote: Hi everyone, I recently adapted the arducopter code to use an indoor RF-based navigation technique for positioning for my drone instead of outdoor GPS. I have a few problems with...
View ArticleSonar usage for altitude during Guided Mode
@guidohuelsmann wrote: While in Guided Mode, sonar altitude seems not to be considered for altitude. Means for example, while walking down a hill with Tower in loiter (guided) Mode, the copter stays...
View Article