Err: crash_check-1
@bellibelson wrote: Hi, I had an expensive crash. I flew in POSHLD to the left with the stick at maximum. After 50 m ore so the motors stoped and the copter crashed destroying gimbal and damaging the...
View ArticleAuto Mission or Script
@ardisd wrote: I it possible to run a series of commands like an Auto Mission but without the GPS Cordinates. for example fly forward 20m, yaw 26 degress, decend to 10m etc. I would like to run a this...
View ArticleCompass set up with Ardupilot is a Fiasco
@Marc_Dornan wrote: Ok, the title of my post was designed to be provocative! It does not reflect my feelings about Ardupilot though. I have been using Ardupilot for years but only recently had the...
View ArticleClik here to view.
How to use channel 9 and 10 for gimbal control?
@Guiboy wrote: I would like to set my RC channel 9 and 10 respectively for tilt and roll of my gimbalI can do it using the gimbal configuration tool of Mission Planner that allows me to select both...
View ArticleIssues Compensating for Barometer Drift Using GND_ALT_OFFSET
@rrr6399 wrote: Has anybody used GND_ALT_OFFSET using the altitude from a ground based Pixhawk to correct the altitude of a copter? I'm seeing poor results with it over longer durations. I'm updating...
View ArticlePixhawk Motors Keep Shutting down
@propflux01 wrote: I don't know if I am in the right place or not, This is my first post here, and my first experience with Pixhawk. I posted on another forum and was directed here. the following is...
View ArticleClik here to view.
Not stable take off in stabilize mode but smooth flight
@Ivosch wrote: Hello,I have almost everytime small issue during take off in stabilize mode @pixhawk and arducopter 3.3. When hexacopter is on the ground and I'm increasing throttle, drone starts to...
View ArticleCant get copter to orbit POI
@Gun-Jam wrote: Hello I have an x8. using mission planner I set a point of interest and a home location and send the mission to the copter. According to the copter wiki when a POI is placed on the map...
View ArticleClik here to view.
Discussion on Indoor Loiter between Randy and Chinese developers
@riddle wrote: Hi, everyone. Nice to meet you. I'm Riddle from China. We are running a China's drone community(DroneChina.org, which is under construction) for some time. DroneChina community has...
View ArticleClik here to view.
Failsafe copter
@Patrik wrote: Hi, I have a problem with arming mine copter. When I want to fly with my copter I can not arm ESC because Mission Planner say "Prearm: chech FS thr value". I set my failsafe FS pwn...
View ArticleCopter-3.4-rc7 available for beta testing
@rmackay9 wrote: Copter-3.4-rc7 is now available for beta testing through the Mission Planner’s beta firmware link (and perhapsthrough other GCSs as well). Changes are below and also in the...
View ArticleCopter jerks during Auto Mission
@Hubertus_Paetow wrote: Short Test Mission with RC7.Everything worked fine except of a jerk two times during the spline flight (at 73700 and again at 101000). Mission planned with Tower Beta. Y6B EMAX...
View ArticleQuad_copter_problem
@calos_alberto_aguero wrote: Help me please !! quad copter project use Board crius aio v2 and Firmware Arducopter rc5 ,mission planner v1.3.33 when I can armed board successful but servo motor is not...
View ArticleIs make/compile different from copter 3.3?
@maxmay wrote: Hi, I make/compile Copter 3.3 no problem, but I get an error when I make/compile Copter 3.4 (something to do with Gawk) Any clues ? What is the difference between the two makes ? Posts:...
View ArticleHeavy Y6 error "ERROR_SUBSYSTEM_EKF_PRIMARY" on rc7
@wifiguru10 wrote: Running 3.4-rc7 on my Y6. Everything flies great, stable, a little drift in pos-hold. Not rock solid, but not bad. I'm getting errors 24-0 and 24-1 on the logs near the end of the...
View ArticleClik here to view.
Trikopter support channel selection on Pixracer
@ZaaaM wrote: Hi there i have ha smal trikopter a quantum trifecta and want to get it fly.but the majer problem is that the servo need to put on chanel 7 but the pixracer has only 6 so where do i put...
View ArticleEKF 2 Error - Possible bug found in EKF 2 - AC3.4 rc 6
@Andrea25 wrote: I was testing AC3.4-rc6.It seems that EKF 2 lead my copter to land itself. The only thing I know is that the copter start to drift a bit in PosHold, and then Mission Planner tell me...
View ArticleFailing to load map
@paulkumz wrote: lam running the command sim_vehicle.py --console --map --aircraft test and after that run wp load ../Tools/autotest/ArduPlane-Missions/CMAC-toff-loop.txt but after all this Xterm just...
View ArticlePPM with Pixracer
@dkemxr wrote: I'm not sure if this is an Arducopter issue or a hardware issue but specific issues with Pixracer have been adressed in Arducopter so I'll ask. PPM input does not work. In my case its...
View Article$ for build/compile instructions
@maxmay wrote: I invested time to build/compile Copter 3.3 for Pixhawk , now I want to invest $ for your copter 3.4 build instructions ! please help ! Posts: 4 Participants: 3 Read full topic
View Article