Quantcast
Channel: ArduCopter - ArduPilot Discourse
Browsing all 21330 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Problem for quad X

@motahary wrote: Hello all Sorry i found a new problem I am in Quad type settings in mission planer ,Put it on Quad X set it up… But when I work with radio control , It works like Quad Plus + … Where...

View Article


Newby considering ardupilot

@Kudos wrote: I am an experience rc pilot mainly focused on helicopters. My working models utilise Skookum and DJI H which I consider to be outdated. My working models are 700 sized flybarless and I...

View Article


What Causes This?

@JEFFGORDON wrote: Plug in the battery to do a calibration and the Right Rear motor starts to spin approx 1/4 rev then stops, (like it got a current spike) while the flight board is booting . . ....

View Article

Helicopter spins (yaw) when trying to take off

@dinnertimebandit wrote: Hello all! I have been slowly making progress on getting my 800 traditional heli to fly. It has a pixhawk2.1. I’ve gone over a lot of the set up with Chris Olsen a month or...

View Article

No GPS in copter 3.5.6 RC1

@pob747 wrote: Hi, I changed from copter 3.5.4 to 3.5.6 RC1 and now the GPS will no longer be detected. Can anyone help with that? Cheers Posts: 1 Participants: 1 Read full topic

View Article


What is the type of the magnetometer on the ublox module of skyviper v2450gps?

@bodhan wrote: Does anyone know the type of the magnetometer on the ublox module of skyviper v2450gps?I used to use HMC5883L,but skyviper doesn’t recognize it.THX! Posts: 1 Participants: 1 Read full...

View Article

Unusual Wobbling in Position Hold Mode

@souvick_saha wrote: HI everyone, I want to address a problem I am facing in my copter. It’s a hexacopter with firmware version 3.5.5 and running with the pixhawk 2.1(cube). In stabilize mode it flies...

View Article

Image may be NSFW.
Clik here to view.

Pixhawk 2.1 suddenly fall Loiter

@alberto.munizaga wrote: Hi, I have this configuration: PixHawk 2.1 , FW 3.5.5, HERE GPS Hexacopter 380kv Arris Motors, 15x55 props 30Amps ESC BLHeli -S 6S 20Apm battery DragonLink Remote So, i was...

View Article


Image may be NSFW.
Clik here to view.

New Build and want to check some messages

@rickyg32 wrote: So I just maidened a new build this weekend and have a few messages in the log that I just want to run past the community. I know this is saying I have an EKF issue and then it...

View Article


My drone(pixracer) lost attitude in guided mode

@Seunghwan_Choi wrote: I sent a message which is go to position to drone. My drone moved but showed adjective motion. The drone didn’t locate position which I set and circled around location. why this...

View Article

How to recognize the ladar sensor?

@111133 wrote: I’m trying to add ladar to ardupilot. I found the source that ‘detect instance’ of ladar type in Libraries/AP_RangeFinder/RangeFinder.cpp but I can’t understand how to recognize the...

View Article

RSSI Modeling in SITL

@teeg wrote: Hi all, I am new to ardupilot, I have a basic mathematical model of RSSI which I would like to include in SITL. Just looking for pointers on how I can go about doing this. Cheers, Sam...

View Article

RC AND MOT parameters - looking for full explanation

@Grisha wrote: Hi. My setting is X-frame quadcopter, Pixhawk-2 controller, U3 motors with 12’ props, Alpha-T-Motor ESC. I am interested in using the full envelope of my motors . After I measured the...

View Article


Obstacle Avoidance not working with HC SR04 sonar

@amitmanish wrote: Hi All, I am using HC SR04 sonar for obstacle avoidance from the given link:...

View Article

Inject Heading into Ardupilot with Fake GPS

@coolkiffings wrote: Hi guys, I’ve got a stereo cam system running on a board attached to my copter. The stereo cam system publishes data into ROS and my PX is connected via mavlink to mavros. I’m...

View Article


Copter 3.5.5 , Cube , Hex Motor Numbering

@Southern-Drones wrote: Hi, so I have a new build as listed above (Hex X). I configured as per the instructions on ardupilot copter setup pages. The problem is that motors 1 and 2 are swapped - I had...

View Article

Arducopter V2.8 after wrong wiring solid red LED and no connection to MP

@MM69 wrote: Hey there, I wanted to conect my gimbal to the APM. I just mixed up Pin A10 and A11 with the SPI Pins. Now i have the following Problem: After switching the APM on the red LED blinks...

View Article


Pixhawk 2.1 won't get off LAND mode

@iamczar wrote: Hi Guys, I’m trying to fly a OctaQuad and when I plug the battery It automatically switches to LAND and stays there I cant switch back to STABILISE or any other mode. And when I remove...

View Article

Battery Failsafe NOT activating

@ScottR wrote: We’re testing a new aircraft with Copter 3.5.5 using a Mauch power sensor. The configuration is correct for the sensor, and we’re getting appropriate voltages and currents. However,...

View Article

How to write log in libraries?

@111133 wrote: I want to write log in libraries… I added the new log struct on LogStructure.h and added log write code in RangeFinder.h… but return error when build… error message is...

View Article
Browsing all 21330 articles
Browse latest View live