Running SkyViper App on Laptop
@JEFFGORDON wrote: I’ve loaded BlueStacks on my Win10 laptop and can save and load the SV App but that’s as far as I can get. Won’t connect to drone or even give me that option. Shouldn’t I be able to...
View ArticleCan not see receive logs tab in AMP V2
@Andy_Keatts wrote: I’m having trouble with AMP V2. I’m trying to locate a lost 3DR solo in thick timber. I have pulled the logs from the controler but am having an issue getting them into AMPv2. I’m...
View ArticleArducopter 3.5 build error
@amitmanish wrote: Hello, I am trying to build arducopter 3.5 on linux with make but getting error “not a git repository” while updating modules using git submodule updqte command. Can anyoe telll me...
View ArticleDetail of Flight log
@ashwani wrote: Does any one having a detail documentation of flight log. As there are many more things which are not updated yet like the units and scaling of voltage in CURR flight log and many...
View ArticleStatic PosHold Loiter Follow Me
@davidbitton wrote: I want to track a moving object as if it’s a POI. More to the point, I want to hover in PosHold over the center of a race track and follow a car around just using yaw. I’m looking...
View ArticleMicroSD Card Broken after formatting
@Thetoxickiller wrote: After formatting my 4GB kingston microsd card the pixhawk won’t log to it anymore. Mission planner gives me the prearm errors: “No io thread heartbeat” and “Prearm: logging...
View ArticleClik here to view.
Altitude Accuracy
@jasonbeach wrote: Over the last couple of weeks I’ve been trying to track down an altitude issue I’m seeing in flight (I’m flying an DJI S1000 with a pixhawk with Copter 3.5.2. During some flights...
View ArticleAutotune - 90 degree roll
@marek2 wrote: Hello guys, today I tried the autotune mode for first time and the result was almost fatal crash. Started in stabilize then switched to loiter and then to autotune. When the aggressive...
View ArticleCrash with 3.5.5
@stxShadow wrote: Hi ! this is my first post in this forum. I had a crash with my endurance copter today and no clue where to look in the log. The Copter had quite a few hours of air time. I used...
View ArticleClik here to view.
PROBLEMS WITH CTUN.Alt
@Ivan_Quesada wrote: I am having terrible issues with the altitude calculated by the copter. The barometer altitude and the sensor altitude are kinda good but the parameter CTUN.Alt is crazy. I made a...
View ArticleHow to calculate the time deadlines for a given task ?
@Tigerly wrote: I’m a beginner of the ardupilot. When I check the source code (arducopter.cpp), I found there are several maximum time here: github.com...
View ArticleAP_RangeFinder_VL53L0X
@shaddow501 wrote: Hello I am using the 3.6 -Dev firmware since it is the only one that should support the VL53L0X range finder. the strange thing is that in “sonarrange” I get values of 0.01 that go...
View ArticleRangefinder use - SF11/C - Oscillating altitude
@Kestrel wrote: Hello again. Working with AC 3.5.5 - Pixhawk 1. I’ve incorporated an SF11/C rangefinder. I would like to use it for terrain following. I have a large QuadCopter that I have tuned to...
View ArticleAccelerometer calibration question
@ajghor wrote: This is my first TradHeli build so some things are new to me… As @ChrisOlson suggested (in one of his posts) the accel calibration can be done with the FC not on the heli so I opted for...
View ArticleDrift of quad in land mode
@ashwani wrote: While landing in land mode, my copter is drifting if air is present. Will controller make effort to counter the wind to enable land with zero attitude and zero velocity ? Is it...
View ArticleCan not send messages from Windows
@HumamHelfawiOptecks wrote: I have run SITL on an Ubuntu machine. I have executed the following command: output add 192.168.1.21:14550 Where 192.168.1.21 is the IP address of an another machine that...
View ArticleFlying Mission Backwards
@Immortal_So_Far wrote: Is there a way to fly a mission from point A to point B with the copter facing forwards, then once point B is reached fly back to point A backwards - in other words, keep...
View ArticleRolls and flips
@Leztec wrote: Has anyone adjusted settings to do rolls and flips? If so what settings did you find worked for you? Here is my attempt at practising a few rolls . Posts: 1 Participants: 1 Read full...
View ArticleLoad custom firmware to pixhawk
@lord_duckfoot wrote: Can anyone direct me to a non-deprecated document on how to load custom firmware to a pixhawk? Everything I find seems to be out of date. The only thing I have found is that you...
View ArticleSIM_SPEEDUP strange behavior
@Crono23 wrote: Hello everyone, i’m facing an issue when setting the SIM_SPEEDUP parameter. if i put a value of 3 / 4 the parameters acts normally. but the simulation speed is still slow for me....
View Article