Clik here to view.
MT7601UN 802.11n soft-disabled in SkyRocket products
@ShadowHatesYou wrote: Having trouble using client mode? I'll save you all ~18+ hours of messing with hostapd/wireshark/iptables trying to figure out what's going on: fccid.io 01736RX24G Sky Viper...
View ArticleStream from multiple skyvipers to vlc
@colorsound wrote: Hi, i read that is posible to stream to vlc. Do you guys know which address command to put in vlc to received video stream from multiple skyvipers ? Posts: 2 Participants: 2 Read...
View ArticlePixhawk2.1 with 2xGPS and 1xLidar?
@Anthony wrote: Since the Lidar is usually plugged in the GPS2 port, how to use a Lidar if I already have 2 GPSs? GPS are Here GNSS modules. Lidar is Lightware SF11/C. Also, slightly unrelated...
View ArticleSimple script using mavros setpoint_position
@sprained_ankle wrote: Hi i'm new to mavros, and I'm trying to use mavros's setpoint_position command. I understand it is a translation of mavlink's SET_POSITION_TARGET_LOCAL_NED. I cam across PX4's...
View ArticleSticks are not maintaining in correct position
@Erno_Rubbik wrote: hello new to ardupilot, I could not see in docs if this is a correct behavior : pushing my sticks to maximum will move channel bars to maximum then reset to zero, regardless if my...
View ArticleMotor test order
@alan wrote: I am buildings a hexa using a Tarot frame. I have connected the motors as per Arducopter illustration with M1 to Main pwm 1, etc.If I use Motor test in MP all of them work except that...
View ArticleCompatible rc transmitter and frame
@ketanco wrote: hello,i will build my first multicopter and plan to use arducopter. can you advise a simple and reasonably priced rc transmitter? i will just build something very simple just to build...
View ArticleClik here to view.
Sonar as primary source of height (at low altitudes)
@Javiercerna wrote: Hi, I'm trying to use my sonar as a primary source of height at low altitudes. Basically, in some of my latest flights, I've seen the barometer going down up to -8 m while landing...
View ArticleCollective pitch output on Tx defined in plane mode
@franguy wrote: Hi ARDU user's, I mounted a Pixhawk on an heli Tirex500. I defined the Tx in Accro mode as recommended. The question is: Because in that mode the receiver does not provide a "pitch"...
View ArticleAuto Pilot 2450
@ksavage wrote: I am new to drones and Sky Viper 2450, and wondering if possible to program for autopilot and adding waypoints for the drone to go to then back home? If someone can point me in the...
View ArticleUsing SILT results for other flight controls
@ecco wrote: Hi everyone, we have a "Matrice 100" from DJI , I’m trying to understand if I can use the results of the flights that simulate with SITL for our drone ?would they be same for real...
View ArticleOptical flow and sonar setting?
@jeongho wrote: Hello, I have a question about optical flow. I would like to use the sonar sensor in PX4 FLOW which I mount on pi xhawk 1.How do I do that? Can you tell me how to configure it?Use...
View ArticleAuto mission problems
@Den_Matiychyk wrote: Hi there, collegues. I'm using Pixhawk with copter 3.3.1 firmware and having problems with Automatic mission. Our Quad have to land twice in a single mission, but on the way back...
View ArticleUsing MAVlink v1.0 or v.2.0?
@tuloski wrote: I wasn't able to understand if from copter 3.5 the MAVlink protocol is v1.0 or v2.0 or if I can choose it.Any help? PS: also mission planner supports MAVLink v1.0 and v2.0 or only...
View ArticleHelp no gps on pixhawk
@MIDGE wrote: HIi have no GPS on my s500 quad build using UBOX M8N GPS module and compass externally connected to my pixhawk flight controller,one of the messages i receive through mission planner is...
View ArticleQground Control Sequence Error
@ksavage1 wrote: I am having issues uploading a mission to my Skyviper 2450. When uploading I get an sequence error (MAV_MISSION_INVALID_SEQUENCE). I read that some people has issues with this but...
View ArticleCaveats using Spline Waypoints
@Iketh wrote: Problem #1 - If you set spline waypoints #1 and #2 let's say 4 miles apart at 200 ft altitude, and if the 3rd waypoint is 20 ft away from wp #2 and 400ft higher, your drone will descend...
View ArticleHow to view EKF position resets in logs?
@Iketh wrote: Would like to see how often the EKF position resets to the GPS position during a flight. What tree and parameter in a log has this info? The variable that governs how often the EKF...
View ArticleIssue integrating Jetson TX1 with Pixhawk
@VTDarrien wrote: Hello, I am currently a new builder in drones. I am working on an autonomous drone with machine vision capabilities using OpenCV however I have problems communicating my Jetson TX1...
View ArticleLightware lidar in Pixhawk 2.1 I2C 2 port doesn't work
@Nija wrote: Am trying to connect Lightware lidar to I2C 2 port in Pixhawk 2.1 to use it as a rangefinder. As per Arducopter 3.5.4 release notes says Lightware range finder are supported on both I2C...
View Article