Building for Pixhawk on Windows10 with Bash on Ubuntu,build failed
@BreederBai wrote: When I use ./waf compiler source code, there is an error，I use the windows10 with Bash Ubuntu： Waf: Leaving directory `/mnt/d/code/V3.5/20170818/build/px4-v2'Build failed-> task...
View ArticleLoiter, yaw and toiletbowling
@patrick_keys wrote: We've all read the documentation regarding compass interference and the infamous toilet bowl effect when in loiter mode. I am flying a custom frame with a Navio 2 board, and have...
View ArticleChanging ATC_ACCEL_P_MAX/ATC_ACCEL_R_MAX/ATC_ACCEL_Y_MAX on large sized heli
@Sunit_Pal wrote: I am trying to fine tune my 800 size heli ( using 3.4.6). I noticed that the tail was very sensitive. So I changed the param ATC_ACCEL_Y_MAX from 270 to 140. This helps a lot and the...
View ArticleCompass not calibrated...or is it?
@X1Aero wrote: I've got a monster X8 reporting two different things. When the radio tx is off the message on the hud is "Throttle below failsafe". Fair enough. But the voice announces compass not...
View ArticleHow to put two drones in one Gazebo simulation?
@cnpcshangbo wrote: Hello guys,I have went through some tutorials to run a Gazebo simulation with a drone in it.However, what I need is to have two drones in one Gazebo simulation and use two ROS to...
View ArticleHex tips over on launch. Desired pitch not zero?
@ooda55 wrote: Hi guys! I've just rebuilt my hex onto a new Tarot FY690S frame and put the latest (supported) firmware (3.2.1) onto my APM2.5.2. It seems to want to take off at a very steep pitch...
View ArticleEKF err crash ck on bench test
@servoman1 wrote: I have 3.52 copter loaded with default settings on pixhawk.on bench with no props.I keep getting ekf error crash when testing without the props on.When I switch modes to saypos hold...
View ArticleFeature request: Full 16ch support for PPM input
@mike wrote: No reason not to have full 16 channel support. Please! Posts: 1 Participants: 1 Read full topic
View ArticleSonar EZ0 pixhawk dont work anymore in 3.5
@felipeviveiros wrote: Why did my EZ0 sonar stop working when I upgraded to 3.5? in previous versions it works normally.I am using in a quad with pixhawk Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
How to two-way communicate between MAVProxy in WIN 7 and SITL in ubuntu 14.04...
@innovation wrote: I have built SITL simulation in my ubuntu ,which successfully running "simvehicle.py --console --map" ,please see following figure 1.The question is there is no reaction in my...
View ArticleAdvice needed with crash from 200ft
@Iketh wrote: Anyone know if a 200ft drop into sand will damage any sensors in the Pixhawk 2.1 or Here gps? Should I replace them to be safe? I was testing failsafe and flipped off the controller and...
View ArticlePixhawk 2 avoidance SF40/c Lightware problem
@michal319 wrote: Welcome.Where in Mission Planner i can find info about everything with SF40C is ok ?Where/how config in mission planner, etc.Connect to GPS 2 port(red,black,orange,yellow from LIDAR)...
View ArticlePLEASE HELP.. Motor speed
@Andy_Zhong wrote: First of all I want to thank you for all the amazing support i had. Anyway my problem is when i just started my throttle two motor started moving then when i continue to move up the...
View ArticleAbout pixhawk arming, changing arming set up
@KelvinClarkson98 wrote: what channels is required to arm the pixhawk? after i changed my setup for my joystick i cannot arm my pixhawk for some reason. Isn't it can be armed when throttle is down(Ch3...
View ArticleDual-Heli frame (FRAME_CLASS 11) Problem
@PittRBM wrote: This new frame type was added in 3.5 but AFAIK it hasn't been tested until now. I have a problem with servos throw, they go to extreme with slight stick input or board movement.I set...
View ArticleDJI 430 Lite ESC
@ScottD wrote: Just about to start assembling my first Arducopter/Pixhawk/F450 kit. I've done a bunch of reading to get myself ready but there's one thing that worries me. I've seen a bunch of threads...
View ArticleAC3.5.2 AutoTune Crash
@oldgazer1 wrote: I have recently updated a 600mm class quadcopter (X-666 frame) from an APM 2.6 (It went up in smoke) to a Pixhawk 2.4.8, This is my 3rd Pixhawk so I'm up on setup, config, and...
View ArticleTilt compensation for lidar
@pierre-louis_Delmas wrote: hi communitytrying a sf11 lidar on my hexacopter with pixhawkconnected to MP i put the copter horizontally at 1 meter above the ground, and of course sonar range is...
View ArticleArducopter manual_control support
@Tangoviktor wrote: Hey guys. Could this manual control support mentioned in this https://discuss.ardupilot.org/t/arduplane-manual-control-support/20983/2 topic be added to the copter AS well? We are...
View ArticleClik here to view.
PreArm: RC Roll not configured
@swshouse wrote: Despite multiple calibrations will not arm Radio cal.png1514x1479 226 KB wont arm.jpg1510x1400 553 KB Posts: 1 Participants: 1 Read full topic
View Article