Log analysis about how to show time
@jason4952 wrote: hello everyone,when I see others’s log file I see the minute on the top of screen ,when I see the log file why I can not see the time?What parameters should I configure ? Posts: 2...
View ArticleSbus flags for failsafe
@flyingw wrote: Does copter use the sbus failsafe flag to identify a a failsafe condition? Please advise. Thanks, Paul Posts: 2 Participants: 1 Read full topic
View ArticleRefuses to switch to Loiter
@umer936 wrote: Hello everyone, My team and I are working on a quadcopter with the APM flight stack. We're using OptFlow and LIDAR. We don't want (and are not using) GPS. Stabilize and Alt Hold work...
View ArticleEKF3 in ride along on 3.5-RC8 with Solo - Log evaluation
@Pedals2Paddles wrote: This is a log from my Solo equipped with a Pixhawk 2.1, running ArduCopter 3.5-RC8. I have EKF2 active and EKF3 in ride along. EKF2 is using the first IMU. EKF3 is using the...
View ArticleLooking for a french developper for specific application of pixhawk2
@arnaud wrote: Hi, i'm looking for a french developper for specific applications of pixhawk2 (dronekit, companion computer,...). Thank you ! Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Flip on take-off after temporary down-rev to Copter 3.2
@Chris_Hardwick wrote: Hey everyone, I'm hoping that I can call on the community to help me with a sanity check. While it might be more appropriate to post in the 3.2 section, I'm hoping that I can...
View ArticletLogs for simulation in SITL
@YesicaVillamil wrote: Where the tlogs (Telemetry logs) are saved for the simulation with SITL? Posts: 1 Participants: 1 Read full topic
View ArticleIs my Pixhawk1 a throw away?
@Peterarnold wrote: In ALT Hold my Pixhawk1 (Ver 3.4.6) will maintain a altitude for a short period then randomly jumps or down a few meters. This behavior repeats itself but seems worse when a gust...
View Article*** Please delete this post
@Crady wrote: *** Delete this post *** Issue resolved Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
EKF Compass Warnings during turns in Auto Mission
@Javiercerna wrote: Hi, I have been flying some time with my quad. When I perform an Auto mission, it all goes as expected, but in every turn between waypoints I always have a warning in EKF: the...
View ArticleRadio channels does preserve last value if cut off the PPM wire
@sergbokh wrote: I'm not sure if this a hardware or firmware problem:I have a Pixracer FC that is connected to FrSky D8R-XP receiver. All works good but when I disconnect the PPM wire from the...
View ArticleArducopter flips on its end or side on take off
@yrjobjorkqvist wrote: Hi all folks. I purchased an F02192-U JMT Assembled HJ 450 450F 4-Aix RFT Full Kit with APM 2.8 from China but cant get it to take off. The propps goes right way and APM 2.8 is...
View ArticleCopter-3.5.0-rc9 has been released for beta testing
@rmackay9 wrote: Copter-3.5.0-rc9 is now available for beta testing and should appear within the next few hours in the Mission Planner's (and other GCS's) beta firmware's link. This is just bug fixes...
View ArticleSerial Data from Pixhawk
@ferocity02 wrote: Is it possible to use the telemtry port to collect data from the Pixhawk such as IMU data, altitude, GPS status etc? I would like to be able to send this data over a serial...
View ArticlePi zero copter 3.5 udp ground control station not working
@awright424 wrote: I have compiled copter 3.5 over and over and after 2 hour plus compilations I run into the same issue regardless of the network I am on. I see the connection to the ground control...
View ArticleRangefinder SF20 Lidar min range
@Andreas_Krauchi wrote: I did install the SF20 according to the wiki and set the parameters RNGFND_MIN_CM to 5 and RNGFND_GNDCLEAR to 8cm.However When the copter is on the ground I get a sonar reading...
View ArticleAC3.5-rc9 compass calibration constants can still be wrongly assigned
@olliw42 wrote: Hey Randy, I open a new issue as suggested in the AC3.5-rc9 release post. The issue: When the compass configuration changes after calibration has been done, AC uses the incorrect...
View ArticleFirst mission item overwritten
@Andy wrote: PixhawkFirmware version: 3.3.3 I create a mission similar like a planned one in Mission Planner and transfer it to the copter via MAVLink.The items are in order:1: Takeoff2:...
View ArticleCamera pointing using ROI
@PhantomRaider wrote: I know this definitely confused me in my initial testing of ROI and I have read some other posts where it has confused some others. Not sure where to post my request and I can...
View ArticleHow can I tone down a twitchy quad?
@Chris_Hardwick wrote: I can't leave well enough alone. When my quads start flying well I seem to think that it's time to fiddle with things. I just have to find out how far I can push. In this case I...
View Article