Radio Failsafe - can't set low value
@Bill_L wrote: HI AllHope this is the right area!I am having trouble setting the low value for the radio failsafe, I've kind of worked around it but was wondering if there's a better way. I'm using...
View ArticleUnable to keep altitude correctly?
@cyclops wrote: Hi, I've had my APM2.8 controller and F450 flying 'ok'. Did a basic autonomous mission and it all worked correctly.I was testing the battery fail safe when it didn't have enough power...
View ArticleAdding servo to control
@ayertay wrote: Hello, How do I add servos to control? For example, I am using AP_MotorsCoax. In AP_MotorsCoax.h I see SRV_Channel *_servo1; SRV_Channel *_servo2; SRV_Channel *_servo3; SRV_Channel...
View ArticleRequest streaming for ESTIMATOR_STATUS STATUS_REPORT
@SoubhiOptecks wrote: Hi I want to receive ESTIMATOR_STATUS STATUS_REPORT messages from the copter. By default, it is sent from the drone so I tried to request it using mavlink_msg_data_stream_pack...
View ArticleArduCopter simulator missing libraries Tutorial
@Michael_Szerman wrote: I have already setup SITL in this tutorial: --> click me <-- I am following this simulation ArduCopter Tutorial: --> click me <-- In the Section of: "Start the...
View ArticleGPS_MIN_ELEV deprecated?
@JakeB wrote: Edit: Found the answer Posts: 1 Participants: 1 Read full topic
View ArticlePreArm: inconsistent Accelerometers
@bendead wrote: Hi guys I have a massive problem, I have a dropix with copter 3.4.6 and since I installed a servo gimbal, my octo wont arm because the the inconsistent Accelerometers. the servo gimbal...
View ArticleSending Waypoints to Multiple Mavs
@tobydilworth wrote: Hi, I have been working on a project that involves sending waypoints to multiple MAVs (very similar to what is now done through the swarming interface, but instead of swarming...
View ArticleCopter intermittently stops between WPs and just slowly climbs
@Gadd wrote: I have had this problem intermittently for a while but can't reliably reproduce it.It will perform as expected most of the time, but now and then it will be between WPs, slow to a stop...
View ArticleClik here to view.
Error while running sim_vehicle.py OSError: [Errno 90] Directory not empty:
@Somya_Agarwal wrote: After following all the steps from http://ardupilot.org/dev/docs/sitl-native-on-windows.html I ran sim vehicle.py using the following command : python sim_vehicle.py -j4 --map...
View ArticleIssue with some parameter
@yrjobjorkqvist wrote: Hi all I purchased an ARF kit from China,...
View ArticleSwitching into Guided from Stabilize with no battery for testing purposes
@MattCon wrote: Hi, I have a Pixhawk on the latest APM software controlling a DJI S1000 octocopter and connected to Mission Planner. I want to test sending MAVLink commands over telemetry to it...
View ArticleSITL is not working properly
@thiagocavalcante wrote: I'm trying to run the sim_vehicle.py script but it cannot run because the script try to download the map from the internet (SRTM Download failed...
View ArticleIRLock does not properly work
@Andreas_Krauchi wrote: Hy During the last few days and weeks I tried to use the IRLock with an MaxSonar EZ4.The first time I used it worked for several landings (6 times). However during the last few...
View ArticleDroenkit-python or FlytOS
@Ahid-Naif wrote: Hello.. I'm planning to work on vision project using APM 2.6 and Raspberry pi.. I believe that I can use droenkit-python or FlytOS.. From your experience, which one do you recommend?...
View ArticleY6 Copter-3.5rc7 Rc_out saturation, logs analysis
@Kiwa21 wrote: Hello everyone, I flew yesterday a Y6A that had a "crash" at the end of the flight.Copter went down quite quickly when one motor reached saturation (pwm to 1954 continuous). What is...
View ArticleTwo identical quads, one doesn't get off the ground
@ccnavio wrote: Tickle me this, Ardupilot people. I have two quadcopters. Same hardware. I have the same scripts running through Mission Planner for both. One gets off the ground, but the other...
View ArticleClik here to view.
Frequent mag switching
@wicked1 wrote: I don't think this is a bug, so the busy developers can ignore... But, I'd appreciate some advice.My flight controller frequently switches the compass it's using.. Is this normal?...
View ArticleHow to get message 32 from Pixhawk
@MattCon wrote: Hi, I have a Pixhawk running Copter 3.4 and I need to be able to get message 32 from it which is MAVLINK_MSG_ID_LOCAL_POSITION_NED that has position data. However, I am not able to...
View ArticlePrecision poshold
@Kiran_Shila wrote: Hey everyone, I am working on a research project at uni and the simple version of my goal is to bring a multirotor to a specific height (about 30 feet) and a certain distance from...
View Article