Clik here to view.
Bad Logging / LOG_DISARMED = 1 / no CAM/TRIGG logs
@Thorsten wrote: Hi all, Background: Testing camera hotshoe feedback LOG_DISARMED = 1 Pixracer Problem: Both CAM and TRIGG messages are not logged Both CAM and TRIGG messages appear in the FMT...
View ArticleParameter Add - Rate of Turn
@pmshop wrote: Could a parameter be added to control the rate of turn for waypoint to waypoint?Waypoint to waypoint during ROI?Setting new ROI?Or proceed to next heading after Loiter_Turns? Current...
View ArticleClik here to view.
Does anyone know why mission planner does not connect to Pixhawk? as it...
@vinhk wrote: Posts: 5 Participants: 1 Read full topic
View ArticleClik here to view.
Where to buy female-to-female Futaba connector wires?
@ferocity02 wrote: I am Pixhawk-ing an S1000 and am looking for some servo wires that have Futaba J female connectors (with the guide tabs) on BOTH ends. I bought some JR style wires but these...
View ArticleFlow setting keeps resetting
@ollenorelius wrote: Running Copter 3.5rc2, and both poshold and loiter work pretty well. The issue is that every time I remove power, FLOW_ENABLE is set to 0. No other settings are reset, only this...
View ArticleCopter-3.5.0-rc4 will soon be released for beta testing
@rmackay9 wrote: Copter-3.5.0-rc4 is being released for beta testing over the next few hours (at the time of this post, the auto-builder is still working on it). This has mostly minor bug fixes over...
View ArticleClik here to view.
EMAX 4in1 ESC with Pixhawk1
@adnan_ul_haque wrote: Hello Friends: I am building PixHawk1 F450 quad and have EMAX 4in1 ESC. While following arducopter wiki Pixhawk ESC issues , seems it will not work !?. I did searched following...
View ArticleServo limit for camera shutter doesn't work
@hexapilot wrote: NEED HELP!Changing values for Max Servo-Limit for the camera shutter in ArduCopter 3.4.6 and 3.5 has no effect (servo alwyas moves to the maximum, no matter what I type in)! In...
View ArticleAutotune with sf11 enable it´s possible?
@cala2 wrote: It´s possible to do pos hold autotune with sf11 enabled, or more convenient to disable it for better accurate? Thank´s Posts: 1 Participants: 1 Read full topic
View ArticleLow KV Autotune problem
@tomerinbar1 wrote: 2017-04-09 08-42-02.bin (302.2 KB) Hello all, I've a problem with autotune my quadcopter.While in the air in stabilized mode it's wobbling a bit, it's get even worst when trying...
View ArticleClik here to view.
Solo on AC 3.5 RC4 testing results
@mtbsteve wrote: eSolo 3.5 RC4 testing results I spend a couple of hours in the air with Solo today and went through most of its features. I used Solex latest version. Stock Solo configuration with...
View ArticleClik here to view.
Live calibration, off center
@S1CAR1US wrote: Has anyone ever seen this? There's sphere starts to form as usual but does so of center, in the back left corner of the screen, therefore the white dots are never hit and never...
View ArticleUncommanded Yaw with 3.5
@Niels wrote: Hi, i'm really not sure if this is a problem with my rig or if it is some problem with 3.5 rc-2 in my case. I'm getting some strange behaviour during flight. The Hex turns left in the...
View ArticleClik here to view.
Error message: Failed to get rally point
@Dorian wrote: Hello, I have program a new board with APM 3.4.6 and when I connect to Mission Planner, there is an error message : « Failed to get rally point » (just after the connect). I don’t find...
View ArticleProblems with the MB1200 XL-MaxSonar-EZ0 analog sonar and frameware 3.5.0 rc4
@felipeviveiros wrote: Problems with the MB1200 XL-MaxSonar-EZ0 analog sonar and frameware 3.5.0 rc4When I installed 3.5.0rc2 the sonar worked normally but after upgrading to 3.5.0 rc3 the sonar...
View Article3.4.6 - Radio failsafe in AltHold causes direct disarm - bench text
@pauljatherton wrote: I just upgraded my hexacopter to 3.4.6 and before flying, thought I would test the radio failsafe behaviour on the bench. Connected/powered with only USB (which powers the Rx and...
View ArticleCustom parameter settings needed on fresh install?
@glider wrote: So I decided to do a fresh install of 3.5 rc4 and start from scratch. Everything is done except tuning. This is a Y6 (Sky Hero 750). It's been almost 3 years, but the original maiden...
View ArticleAPM 2.8 flight controller doesn’t output
@Munkhjargal_Nymsuren wrote: i built my first quadcopter f450. APM2.8 flight controller, FS-TH9X transmitter, FS-R9B receiver simonc 30A ESC etc. problem is motors not rotating. if connect receiver...
View Article[SOLVED] 3.5.0-rc4 Looses frame type on reboot
@varesa wrote: I just got a Pixhawk Mini (=pixfalcon?) from 3DR and flashed 3.5.0-rc4 on it. If I try to arm the unit I get the following message:"PreArm: Motor Interlock Enabled" It doesn't matter if...
View Article3dr Tower 4.0 problems
@Obrien50 wrote: Follow me won't work using the tower app. Posts: 1 Participants: 1 Read full topic
View Article