Problem with frsky+rssi
@turborocket wrote: Hello to all! today i went to setup the rssi from my x8r(last firmware eu lbt), adding the Resistor/capacitor filter, as suggest from arducopter wiki. Well, its not perfectly...
View ArticleEKF variance w/o any GPS or mechanical issue....why?
@imrj wrote: running hexa with 3.4.4 and for the first time since running 3.4 while on a simple loiter I had a sudden EKF variance and a switch to failsafe (althold in my parameters).....why did this...
View ArticleIs anyone using DO_SET_ROI?
@Sully wrote: We have setup a WP plan with: TakeoffWaypointDO_SET_ROIWaypointDO_SET_ROIWaypointDO_SET_ROILAND It takes off, goes to three waypoints and lands, the quad never turns to ROI. We attempted...
View ArticleCh IN, but no CH OUT
@jeraldthompson wrote: Cannot find anything on this problem on line, so here goes: Up until just a day or two ago, I was able to see all the Ch_IN and Ch_OUT traces for roll, yaw, throttle, and pitch...
View ArticleClik here to view.
Cannot Calibrate Compass, Either way
@Niels wrote: Hi, building currenly my 4th multirotor and I'm facing some problem I never encountert before. During compass calibration all the points are in one axis. I attache a picture. The first...
View ArticleClik here to view.
Question about RC OUT
@cookmangr wrote: I have a X8 coaxial with sunnysky 3508 700kv motors and 13×5,5 on the top and 12×5,5 on the bottom I want to check the difference at RC Out PWM I see at my logs that there is RC OUT...
View ArticleIs Receiver RSSI Supported through SBUS?
@flyingw wrote: I have a receiver that can inject its RSSI onto a channel in its SBUS output. Can I use ArduCopter and Mission Planner to display that value on Mission Planner? If so then what...
View ArticleQuestion about state of SITL/HITL
@msadowski wrote: Hi all! I read a bit docs on SITL here. Can anyone of you tell me if all the docs related to SITL/HITL up to date? Is it possible to use SITL with jmavsim? Is there anything in...
View ArticleShutter Config Requirements
@Sully wrote: What is required of a channel to be eligible to be assigned to Shutter on the Camera Gimbal page? I'm working with Copter 3.4.5 If I select any of the drop down choices (Ch9 - Ch14,...
View ArticlePros / cons of enabling Galileo satellite positioning on Ublox M8N?
@juzzle1 wrote: The release notes for the Ublox M8N v3.01 firmware states: 'The recommended maximum navigation rate supported is 5 Hz for standard multi-GNSS operation (GPS + SBAS + GLONASS + QZSS)...
View ArticleClik here to view.
Mavproxy module
@najam wrote: when i load my module i get this error. can anybody tell me how i can remove this error. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Error in loading mavproxy module
@najam wrote: when i load my module i get this error. can anybody tell me how i can remove this error. Posts: 1 Participants: 1 Read full topic
View Article5 bips on fly 6 times in 1 mn flying?
@shyriu42 wrote: hello what does it mean 5 bips during flying on apm 2.8 ? 3 or 4 times in 1 mn ? what is the problem ? the quadcopter flying well but with this bips Posts: 1 Participants: 1 Read full...
View ArticleHow to set POI in the air - without MP
@sn0west wrote: Hi everyone, Is there a way to set the poi while the copter is in the air by switching a switch on the rc? I would like to use circle mode anytime I want. Hovering over an object set a...
View ArticleCopter-3.5-rc1: LIDAR-Lite 3 Rangefinder No Signal
@lasakro wrote: After upgrading from 3.4.5, where the Rangefinder worked, to 3.5 RC1 it stopped working. I enabled EKF-3 with the same results. APM Planner 2.0.24 Quick Display no longer shows a...
View ArticleFail to download new firmware "The operation has timed out"
@mauritzg wrote: Hi Guys . Is there something wrong with the Firmware server? I'm getting a "The operation has timed out" when I try to download firmware in MP. Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Can't calibrate compass after I have already done it before
@mauritzg wrote: Has anyone came across this issue and know how to solve it. I'm busy setting up and Hexa with a Pixhawk. My first one was a APM 2.8 . I have gone through all the calibrations but for...
View ArticleInterpreting a log to investigate toilet bowl effect
@flyingw wrote: Had a couple of flights today where I tested loiter mode. I observed some toilet bowl effect. What can Iearn to check in the log to see how to resolve the problem? I've attached the...
View ArticleClik here to view.
RC-Timer Mini ArduFlyer V1.0 Servo Range
@CrYo_ZA wrote: Hi Guys! My apologies for bothering you guys, my name is Rick and I am quite new here. I have been playing around a lot with different versions of the Pixhawk Flight controller as well...
View ArticleTakeoff in PositionHold?
@R_Q_Robert wrote: Hi AllI want to know is it possible to takeoff in PositionHold mode.?? Posts: 4 Participants: 4 Read full topic
View Article