No map click position available
@hmolintas wrote: Hello, Every time I try to click “Fly to” and set the altitude, I get a “No map click position available” error and the copter doesn’t move. I also get the error of "Error in command...
View ArticleIncrease frequency of IMU data without change in firmware
@rrsaxena92 wrote: I want high frequency(around 20Hz) IMU data from pixhawk for my application. This is all that I have tried I tried with wireless telemetry radios first but I knew those are not...
View ArticleLIDAR RF MINI problem on Copter 3.6.4 Hexa (pichawk)
@AdHd22 wrote: Hi guys! Could you help me with LIDAR TF MINI on my hexa drone? I got weard crash list time when i was flying. Everything was fine, first flight went 100% correct. Battery Change and...
View ArticlePixhawk Mini Roll and Pitch axis issues
@Mehrankhan wrote: Hy we are using Pixhawk4 Mini and when we give a roll or pitch movement to our copter its behavior is unpredictable and it execute a certain twitching and crash i attach the log...
View ArticleTail Bouncing Issue
@rotems wrote: Hello, I have a Trex 700 with Pixhawk 2.1 and when I’m flying in Loiter mode the tail is bouncing up and down during forward and backward flight. Maybe someone know what could be the...
View ArticleClik here to view.
Matek F405 CTR Copter 3.6.9, PreArm: Logging not started / Logging failed
@Dmitry wrote: Hello. Has anyone encountered this problem? Formatted a SD card (4GB U3) in the format of FAT or FAT32, inserted into the flight controller. When I try to disarm, I get the message...
View ArticleClik here to view.
Y 6 copter build
@Barry_Bolton wrote: Hello everyone. I wan to convert this Hobbyking h600 to a y6 and need some advice on FC placement. The distance from the middle of the front motor to the middle of the rear motor...
View ArticleCopter 3.6.9 and Cubie Yellow
@tomekr wrote: Hi All Today I get new Cube Yellow for test I uploaded copter 3.6.9 firmware (MS detect Cube Yellow) but I have problem Mission Planner says Initialising APM and thats all, in QGC I see...
View ArticleConnect Pixhawk to RealFlight 8
@Patrick_Danielson wrote: I am trying to import my Pixhawk parameters for an Octocopter hopefully via SITL into RealFlight 8, following this guide...
View ArticleClik here to view.
AC 3.6.9 Crash with IR-Lock and PLND_EST_TYPE enabled
@mtbsteve wrote: After 2 years this defect was initially reported, it is still open with Arducopter 3.6.9 along with the IR-Lock sensor for precision landing. When PLND_EST_TYPE is set to 1, the...
View ArticleV2450gps unhooking from gps
@Brad wrote: I have a V2450gps and whenever I use the right joystick it disengages GPS and goes to the manual mode … I don’t recall this happening till just a couple weeks ago… I’ve had more than one...
View ArticleMultiple geo views-Need to change them
@Jerry_Prado wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleUWB fake gps(GPS_INPUT) can not hold position in loiter mode
@Huibean wrote: Currently I am testing uwb system with ArduCopter, using sky viper fly indoor, I am inputing the pos value with mavlink (GPS_INPUT), params change with GPS_TYPE to 14(MAV), the uwb pos...
View ArticleClik here to view.
Crashed Log Analysis
@AnnieME wrote: Hi, We faced with a crash of our quadcopter which uses a Cube (ArduCopter 3.6.9). These are the details: First flight was conducted for about 5 minutes, which went fine. Second flight...
View ArticleCamera switch on/off using relay pin
@Mallikarjun_SE wrote: Hello guys, I have been using 2 relays on cube autopilot for a while now. One to trigger shutter and one to switch camera on/off (DIY Multiport cable for Sony camera). The issue...
View ArticleHelp in analyzing the log file,arducopter v 3.6.9 -copter crash
@Sudiptabir wrote: This was second flight, copter crashes after take off within minutes, 2 17-07-2019 16-57-44.bin (313.3 KB) here is the .bin file. Pixhawk 2.4.8 Ublox M8N gps+compass, external...
View ArticleFPV Helicopter recommendations / tipps
@Pakman wrote: I am looking for a helicopter kit, which has more endurance than my usual Electric Platforms (550 to 700 classes). Most probably this should be a nitro powered Helicopter… It should...
View ArticleAC3.6.9 unable to calibrate ESC
@NiharikaPatel wrote: @rmackay9, We have an Iris+ with a pixhawk which had the AC3.2.1 firmware that we updated to AC3.6.9. On updating we found that we were unable to calibrate the ESC. We tried two...
View ArticleSBUS Output Not Working
@rge99 wrote: I am assuming and trying to use the SBUS output to daisy chain the SBUS between my flight controller and gimbal but, I am seeing no output on the SBUS out port. I set BRD_SBUS_OUT...
View ArticleMISSION Continuation in AUTO mode
@charles_linquist wrote: If I am flying a Mission, and all waypoints are set to 100M, then, between waypoints 2 & 3, switch to loiter and manually climb vertically to 200M, then switch back to...
View Article