RTK for altitude in 3.4?
@cgormley wrote: Is there any way to use a Piksi RTK to control the altitude instead of relying on the barometer. In a flat field during auto missions I get a swing of almost 15 ft between waypoints...
View ArticleTrying to tune 250 quad with Pixracer board
@iseries wrote: During the tune the copter suddenly turned 180 degrees and faced me. The logs show that EKF turned the copter but don't know why. This happened twice and I have provided a log. Log:...
View ArticleData_ekf_yaw_reset
@tabascoz wrote: Hello, Could someone please explain to me the meaning of those ev 62 DATA_EKF_YAW_RESET ? I'm getting a few of them and don't know if they are OK or if they mean something that I...
View ArticleStorm32 via Pixhawk or Rx
@eyber wrote: Hi, I have pixhawk and storm32 1.31. I use AC 3.3. I bought 3 axis gimbal for sony nex from goodluckbuy. But I don't know how to wiring storm32 and pixhawk. RC inputs via pixhawk or Rx....
View ArticleStock E-Sky Belt CP v2 with AMP 2.8 IS IT POSSIBLE!
@ivant wrote: Hello, I've just repaired my Stock E-Sky Belt CP v2 with 6ch transmitter from crash. Now i want to use AMP 2.8 with ardupilot in stabilize or AltHold mode to assist me until i am...
View ArticleCrash on 550 quad with Pixhawk on 3.3.3
@DaveP wrote: I have been having considerable problems with my 550 quad after having installed a Pixhawk clone from RcTimer. I downloaded Copter 3.3.3 hoping it might cure the wildly rolling craft...
View ArticleHello here a problem with AutoTuning pixhawk
@cuchara wrote: when I put the drone in AutoTuning the drone loses altitude and crash Any idea what I can do?Thank you Posts: 2 Participants: 2 Read full topic
View ArticleAPM copter 3.3.3 Guided mode with companion computer
@Muttle wrote: Hi all,I have a trex450 conventional helicopter running a px4 with an intel edison as a companion computer. This system has a custom build linux ubilinux install and runs ROS Indigo and...
View ArticleUnexpected throttle zero in pos hold
@Hubertus_Paetow wrote: Today after flying around in stabilize i switched to pos hold and contiued flight. after about a minute without any action the motors stopped and copter started falling. I...
View ArticleCommands change with copter orientation
@mickaeldes wrote: XHi, I bought a DIY drone on amazon and I mounted it. I did all configurations thanks to Mission Planner. And I tried my first fly... but during it, the commands changed with the...
View ArticlePlease help 2.8 how do you download the soft where f
@wacked wrote: I have a new 2.8 how do you download the soft where for it? I have windows Vista.Thank youTerry Posts: 1 Participants: 1 Read full topic
View ArticleNewbie Unable to link flight controller help please
@Dylanmaguire wrote: Hey guys and thanks in advanceI purchased my first copter over the weekend and loving it per than being able to sort it out hahaha. I have downloaded apm planner 2.0 and have been...
View ArticleAfter 19 minutes in Loiter ,150° Yaw rotation and went gently down vvithout...
@lucamax wrote: Pixhawk last revision with 3.3.3 firmware. It is not the first time it happens, but previously I suspect bad compass , Gps gliches, solar storms .before flight I check everything twice...
View Article[SOLVED] Logging issue, no logs generated. SD Card contains symbols in filenames
@Foxgguy2001 wrote: I've been having some trouble getting my pixhawk to produce logs. When attempting to download via mavlink, i get "no logs to download" if I remove the SD card and have a look, it's...
View ArticleClik here to view.
Help analyzing log. Crash after start
@Kudykam wrote: I have pixhawk with 3.4. RC1. It flies fine for a long perdio of time. Today I start in alt pos mode and imediatelly saw a very bad reaction on joystick. After 15 sec it crashed.I dont...
View ArticleClik here to view.
AutoTune should better get removed
@Daniel_Frenzel wrote: I tried AutoTune now several times(250 class) and the results are all dangerous. Firstly, the Tuning takes ages and the result is not even close to be flyable. See the picture....
View ArticleAfter Auto Tune copter flies like a drunken sailer
@iseries wrote: I have a 250 size quad flying a Pixracer controller with the battery mounted on top of the copter.Did auto tune in Pitch first and then Roll.Pitch auto tune seems fine and flies...
View ArticleLarge hex crash, been working perfectly on 3.4rc1 and rc2?
@X1Aero wrote: I've got a 960mm hex with 18" props and 288kv motors that went crazy today. It's been flying 3.4 since it was released for beta and flew great. I notice the tuning could be better so I...
View ArticleZero EKF wind speeds in copter?
@lzl200102109 wrote: Hi everyone, I am trying to obtain the EKF wind speed estimates in datalog from a new 3DR IRIS+. However, they are all zeros currently when I visualize the variables under...
View ArticleRate yaw I gain
@Mark97564 wrote: Does anyone know why I can't adjust the I gain for rate yaw on pixhawk running copter 3.3? I can type a value but once I hit enter it just reverts and I can't save my new numbers to...
View Article