Randomly motor problems with FC APM 2.6
@CopterWolf wrote: Goodmorning everyone, I would like to expose my problem to which I can not find a solution. First of all, I list the characteristics of my Copter: Frame DJI F450 4 FullPower 2814M...
View ArticleArducopter 2.8 Arming
@Markus50 wrote: I have a Quadcopter which I have built, I am using the Arducoptor 2.8, I have nothing else as far as accessories are concerned, (not yet anyway), so I have just got my receiver, I...
View ArticleV Hexacopter frame
@ddlopo wrote: Hello, Can someone tell me if with arducopter I can configure a V hexacopter? Put a distribution of engines in V. Thank you Posts: 1 Participants: 1 Read full topic
View ArticleTelemetry to x9d+ via direct sbus?
@skypuppy1 wrote: Is there some physical reason we can’t get telemetry data piped through the standard sbus from the Cube out to an X8R, WITHOUT having to add yet another cable on a serial line to...
View ArticleTradHeli Changes in Copter 3.6.0-rc1
@bnsgeyer wrote: TradHeli users, I just wanted to call your attention to the release notes regarding tradheli changes. I made a comment on @rmackay9 blog on the release of Copter 3.6.0 rc1 and wanted...
View ArticleHow to Set Negative Pitch to Increase Forward Speed?
@JEFFGORDON wrote: What can I do to increase forward speed? Perhaps setting negative pitch somehow? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
GPS Guided Modes not Working ARDUCOPTER 3.5.5 OCTAQUAD Pix2.1 Here GPS
@skyhook wrote: HI All I am having trouble with GPS guided modes (Pos Hold, Loiter, RTL) POShold: When entering POShold from lateral movement, the copter brings itself to a stop. But after a second or...
View ArticleFLYAWAY NIGHTMARES . . . post your horror story
@JEFFGORDON wrote: So that others may learn from the experience, and take corrective action. Posts: 1 Participants: 1 Read full topic
View ArticleUse standalone navigation module with ArduCopter
@chrs wrote: Hello, I’m working on a project where we will utilize a complete standalone navigation module (attitude, position, velocity etc etc) and feed that information in to use in its attitude...
View ArticleClik here to view.
PX4FLOW Optical Flow Camera Board Overview
@Alex_MH wrote: hello guys, I’m trying to get the altitude back using the soanr built into PX4flow, I use as OcPoc zynq mini hardware, when I activate the sensor with mission planner, I connect the...
View ArticleNo Battery Failsafe?
@OldGazer wrote: Installed rc1 this morning and ran into a couple of issues. First off what the heck happened to the battery failsafe? The low voltage and remaining current capacity settings are...
View ArticleChoisir le bon model pour hélicopter ?
@laurentchud wrote: Bonjour, J’aimerais un pilote automatique pour hélicopter .Je ne connais rien et je suis perdu pour choisir le quel je dois prendre. C’est pour installer sur un Trex 450 ou 550 en...
View ArticleClik here to view.
Pitch axis Oscillation in auto mode, big copter
@mxapaza wrote: Hi, I have a problem in auto mode with a quadcopter, flight well at started but a little oscilations begin after a few waypoints. It flight well in stabilize and Althold, in Loiter...
View ArticleMissionPlanner Com Port
@brierfox wrote: I’ve spent the last 2 hours trying to figure out which COM port is acceptable when setting up my first shot at Mission Planner… Using Linux, this has been one hell of a journey...
View ArticleIris+ seem to have changed his controls since updates
@Marc-Andre_Noiseux wrote: I tried everything , I’m depressed. Bought a Iris+ drone in the end of year 2014 . My drone isn’t acting like it was when props off in 2015. When I bought it , it was...
View ArticleMission Planner-Pixhawk-GPS Antenna Tracker
@Hunter wrote: I would greatly appreciate if you help me I’m working on antenna tracker for tracking Multirotor but it is not able to track the Multirotor just spinning around itself without stopping...
View ArticleClik here to view.
Yawing After Crash
@Caleberg wrote: Hello! I am a long time creeper and first time poster to the forums, so please educate me on any best posting practices where I am lacking. I am an APM noob and willing student. I...
View ArticleADS1115 - mapping
@shaddow501 wrote: Hello Is there any guide how to work with the ADS1115? I would like to use the ADS1115 as GPIO pins but I do not know how to call them or map them? Basically using range finder...
View ArticleAdd the code to change the voltage of TELEM2 pins, but there is no change
@c1466207310 wrote: Hi, I want to change the output voltage of TELEM2 pins to 0V,so I download the pixhawk_toolchain and ardupilot code,and I just add some very simple code in ArduCopter.cpp like...
View ArticleSSD1306 doesn't come up
@StefanG wrote: FC: Pixhawk 1 clone FW: AC 3.5.5 (27229c83) Display: Generic 0.96" SSD1306, I²C address 0x3C Problem: Display doesn’t come up - stays black Debugging done: Verified NTF_DISPLAY_TYPE is...
View Article