Quantcast
Channel: ArduCopter - ArduPilot Discourse
Browsing all 21347 articles
Browse latest View live

Obstacle avoidance using TeraRanger One not working properly

@Aashika_Chitagupi wrote: Hey, we have a copter fitted with a TeraRanger One in the front to make it maintain a distance of 2ft from a wall. We have changed all the necessary parameters as show in...

View Article


Image may be NSFW.
Clik here to view.

Best MOT_THST_EXPO value for T-Motor Flame ESCs

@CLabeck wrote: Hi, finished my latest build and about to start tuning. I am using T-Motor Flame ESCs (and matching T-Motor motors/props too). I read here in another thread that T-Motor ESCs apply...

View Article


Image may be NSFW.
Clik here to view.

Althold is not good

@sakirpolay wrote: hello all my new hexacopter fly well in stab mode. but couldnt do proper althold tuning. so i am having some unwanted vertical small movements that shouldnt be. hobbyking thorax...

View Article

Searched and Stuck

@pyrate wrote: Removed do not see a delete optionb Posts: 1 Participants: 1 Read full topic

View Article

Removing rc in guided mode

@amitmanish wrote: I tried changing mode to circle mode using dronekit in guided with mavlink command. I had to use rc override to keep constant altitude in circle mode. Everything works fine except...

View Article


Helicopter Control Gains Unit Conversion Question

@Tudole wrote: Hi Everyone, I have a question to the unit of the control gains. I’ve briefly looked into the code. It seems like to me, the rate is in centidegree before it’s multiplied by the gain....

View Article

Uneven servo outputs APM 3.2

@buraker wrote: Hello All! This is my first question here. I have built a new quadcopter using s500 frame. I calibrated both accelerometer and compass using mission planner. I am having problem with...

View Article

Ublox GPS Config file

@Pomaroli wrote: Hi the download link provided in the docs for the ublox config file is not working : https://github.com/ArduPilot/ardupilot/tree/master/libraries/AP_GPS/config where can i get the...

View Article


Image may be NSFW.
Clik here to view.

What setup should be used for this type of drone?

@qmayberry wrote: Any ide’s what frame type should be used for setting up this type of drone? Octocopter.jpg1000x644 255 KB Posts: 3 Participants: 2 Read full topic

View Article


Uneven servo outputs APM 3.2

@buraker wrote: Hello All! This is my first question here. I have built a new quadcopter using s500 frame. I calibrated both accelerometer and compass using mission planner. I am having problem with...

View Article

Serialx_protocol parameter does not exist

@parnil wrote: Hello Everyone, I have got ArduPilot 2.8, to which I can connect mavproxy and it says ArduCopter V3.2.1 (36b405fb) version is running. Problem that I am facing is that I am not seeing...

View Article

Navigation tuning

@Oussama_Bekkouche wrote: Hi, Is there any docs for ArduCopter navigation tuning ?? is it the same docs for ArduPlane : http://ardupilot.org/plane/docs/navigation-tuning.html Thank you in advance...

View Article

Loose level when switching from Acro to stabilize

@Pomaroli wrote: i’ve update today my copter to latest 3.5, setup and normal flight was pretty nice. But, following issues i’ve encoutered When doing a lot of acro and loopings in Acro mode and then...

View Article


My SkyViper, Linux, and Me... Help?

@brierfox wrote: I am starting to get a little stressed after several hours of trying to figure out if a way even exists to get my SkyViperGps 2450 to be able to participate in the awesomeness that I...

View Article

Tarot gimbal and Pixhawk

@NoPro wrote: Has anyone connected the Tarot zyx 5V gimbal with the Pixhawk? I’m able to pan and tilt through it, but I think it’s capable of being updated from a fc to help with roll correction. I...

View Article


No XYZ values for magnetometer

@Dude wrote: Where is the magnetometer located in the SV? I believe the one in mine has stopped functioning. I tried doing a calibration and the fixed was successful but no change. The rotating never...

View Article

Quad Unable to Arm Pixhawk, Copter 3.5, AT9S Transmitter

@ZL647 wrote: So far I’ve been unable to arm using the transmitter. The Quad boots up, finishes all pre-arm just fine, but holding throttle to bottom right doesn’t arm. I CAN arm it using Mission...

View Article


Skyviper 2018 lineup leaked in this video

@lordneeko wrote: Not sure where he got the info, can’t find it on Google. but just as I suspected, they have a 4th Journey model, which even advertises the advanced AP features like waypoint...

View Article

Newb Questions U Were Afraid to Ask

@JEFFGORDON wrote: Okay . . . I’ll go first, but feel free to contribute . . . Where is the SkyViper wiki? When you hit EXPORT on the SV app post flight . . . where and what files “export” What do the...

View Article

Faster waypoints download and upload

@radiof8 wrote: Hi there! I’m writing my own mission planner specially for my purposes. One of things I want to implement is generating waypoints automatically. I have uploading and downloading...

View Article
Browsing all 21347 articles
Browse latest View live