Problem Compas calibration (do not calibrate the dron)
@kchopilot wrote: Hello friends.Something inexplicable has happened, has updated the mission planner and now I can not calibrate the drones (2 different APM arduoptero, ardupailot)General dataApM 2.8,...
View ArticleApm 2.8 y gimbal a followme
@Henrymunoztorres wrote: Hello, my name is Henry, I want you to help me with a problem, having a Hexacopter, with apm 2.8, to this I have installed a gimbal of 3D, the problem is presented when I...
View ArticleAbout without-GPS flight with Copter 3.5.3
@Alp_Ozdemir wrote: Hi there, I didn't know who to ask for help so I turn to hereI want a simple, manual flight without gps such as: Take off, climb to 100m alt. (via barometer) Fly north @10m/hr for...
View ArticleCopter with Marvelmind can't hover in place. It is oscillating
@joseocasio wrote: Hello, I have a Copter using the marvelmind indoor "GPS" and I am trying to make it loiter in place. According to the Marvelmind dashboard the tracing of the copter is perfect. Is...
View ArticleSurprising message: Warning! Connection to the Streaming GPS Drone has been lost
@johngithens1 wrote: The subject message on my iPhone 5S (including "Please check the battery is fully inserted, charged and that you are connected to the drone in your devices WIFI settings.") has...
View ArticleOptical flow and aiding mode
@kpihus wrote: Hello, I'm trying to get optical flow working. In overall it works quite fine, bit unstable tough, but probably because I'm using analog sonar at the moment. But it's little confusing...
View ArticleClik here to view.
Rangerfinder Lidar SF20 don’t work
@Dorian wrote: Hello, I can not run a Lidar SF20 with APM Quad v3.5.3 firmware.Mission Planner displays "Bad Lidar Health", and "sonarrange" remains at zero.I installed it in I2C then in serial...
View ArticleNewbie - Trex 600 / Pixhawk / Taranis E setup
@Oliver1 wrote: Hello, I have been flying helicopters for a while and recently bought an Aperture (Hobbyking) drone which uses a Pixhawk compatible controller. In the setting I found that it can be...
View ArticleClik here to view.
Heading issue at startup with HERE GPS module
@Juan_Manuel_Gonzalez wrote: Hi guys, I am very concern with this discussion: github.com/ArduPilot/ardupilot Issue: Cube/Here GPS heading off by 90deg sometimes opened by rmackay9 on 2017-07-20 closed...
View ArticleClik here to view.
Integrating a different air module with HERE base module for RTK
@Juan_Manuel_Gonzalez wrote: Hi guys, While the heading problem with the HERE GPS air module persists, I cannot rely on this module to fly my copters: github.com/ArduPilot/ardupilot Issue: Cube/Here...
View ArticlePixhawks 3.5.3 AltHold Crash. Pos(Vert) issue?
@crazy1pilot wrote: I recently upgraded my system to Copter 3.5.3, I flew about four short flights and everything worked well (AltHold). All flights were done inside in a warehouse. The next day I...
View ArticleHow to setup helicopter for AP_ICEngine and throttle servo
@lutinplunder wrote: I am building a 2.5m synchrocopter powered by a DA150L and am having trouble finding documentation on how to setup the AP_ICEngine to control the engine and setup a throttle...
View ArticlePixhawk startup error IMU start failed Check BRD Type
@Gregmaan wrote: Hi,Since updating to 3.5.x sometimes I get the Error IMU Start failed Check BRD type.Setup the brd_type from auto (0) to Pixhawk (2) does not help. Never had such issues with AC 3.4.x...
View ArticleGeo fence RTL altitude
@Bryant wrote: Does the RTL altitude work like RTL mode? What I'am trying to find out is,if you leave value at 0 will it return at current altitude?Any reply would be thank full.I have searched with...
View ArticleCopter V3.5.3 Mission Planner 1.3.50 THR_MIN not found
@henrik04 wrote: I guess the THR_MIN parameter has probably been renamed as Auto Analysis of a log fail to find THR_MIN? Thank you. Posts: 1 Participants: 1 Read full topic
View ArticleArduino uno input for copter control
@otter wrote: Hey thereIve been building an Arduino Uno based quadcopter over the last few months and been hooped on trying to get it off the ground. The main limitation is lack of processing power to...
View ArticleHML650 gear controller troubles
@DaddyToTwo wrote: Hi everyone! First, let me apologize for the novel I’m about to post. I am having an issue with pixhawk and The HML650 retractable landing gear. The pixhawk is programed correctly...
View ArticleDefinition of flight mode (horizontal movement)
@Winfriedrijssenbeek wrote: For a number of applications (spraying in agriculture) or taking loads that only can be carried level, one can imagine a multicopter that can move forwards or sidewards...
View ArticleRecommended minimum prop tip clearance on quad
@aduncan wrote: Turnigy S500 Quad, Emax 810 Kv motors, Pixhawk. With 12x5 Aeronaut props tip clearance about 35 mm the quad is perfect . But with 13 inch props and 9mm clearance the motors pulse about...
View ArticleIndoor Navigation using HTC Vive
@JustFineD wrote: Hi,I would like to navigate my copter in lab using HTC Vive controller attached to the drone.The idea is to receive the position of the controller in my laptop and then inject this...
View Article