Change home base
@jumank wrote: Is there a way to make ArduCopter SITL (with MAVProxy, DroneKit API, and APMPlanner 2.0) initialize somewhere else in the world besides Canberra model airport? Posts: 1 Participants: 1...
View ArticleClik here to view.
Automission misses WP2, FlyAway
@keohr wrote: Yesterday I flew for the first time my two years old 450 Quad with FW 3.4.6 (upgraded from 3.3.3)It was also my second attempt to fly a mission.The first battery all went smooth. The...
View ArticleAllow for user defined roll input max
@R_Q_Robert wrote: Hi All I using Pixhawk v1AC3.4.6Quadcopter How do i limit my ROLL Angle in AUTO flight mode?? Posts: 2 Participants: 1 Read full topic
View ArticleHow to limit ROLL ANGLE in AUTO mode?
@R_Q_Robert wrote: Hi Guys I want to control my roll angle in AUTO mode. What is the parameter for it ?? Posts: 1 Participants: 1 Read full topic
View ArticleDodeca-Hexa ESC Wiriing and Propeller Direction
@R_Q_Robert wrote: Hi All A new frame class dodeca hexa is added recently in Copter Firmware. But there are no details about how to connect ESCs to Pixhawk and there relevant Propeller Directions. Any...
View ArticleClik here to view.
Battery Monitor Works on Pixhawk 1 but not Pixhawk 2 Cube
@DivenParker wrote: I'm currently having issues with getting the battery monitor to work properly on my Pixhawk 2 Cube from ProfiCNC. I thought that perhaps I had the wrong pins selected, but the...
View ArticleAC3.5-rc11 dual gps issues
@olliw42 wrote: I've reported pieces of this somewhere before, but it might not have been noticed. I've spend now a bit more on it, and teh issue persistet, so, next try. config: AUAV-X2, one "normal"...
View ArticleClik here to view.
AC3.6-dev dual gps issues
@olliw42 wrote: I've played around with this configuration config: AUAV-X2, one "normal" gps+mag on uart and i2c, one uc4h uavcan gps+mag on can, AC3.6-dev of tonight, latest MissonPlanner...
View ArticleCustom uses for the analog pins on APM 2 board
@Rani_Khalil wrote: I am currently working on a project that requires some custom modifications to the arducopter source code. I have experience writing arduino code but this doesn't seem that...
View ArticleClik here to view.
Hexacopter wont lift
@ChristophZaipts wrote: Hello, fellow members of the community, I have a problem with lifting my copter from ground. My setup is an APM 2.6, a DJI F550 frame (clone), six (obviously) 2212/920KV...
View ArticleWhat ESCs Support Motor RPM Logging?
@lzl200102109 wrote: Hi, I am using ArduCopter v3.3.3 right now, and I would like to obtain RPM readings for the motors. I saw that there are several ESC messages defined in the firmware in the data...
View ArticleAC3.5-rc11 Oscillation/instability from motors 3 and 4
@justsomeguy1983 wrote: I just flashed AC3.5-rc11 on my quad, I'm running a pixhack with 4006-380kv motors, hobbywing 40a xrotor escs with the latest blheli spinning 15" props. After flashing...
View ArticleR12DSM Receiver Help!
@Bowman1949 wrote: Relatively new to multirotors. Have Radiolink R12DSM mini receiver. Is SBUS. How does one connect SBUS to a controller. I want to use on APM 3.1 and KK2. As am working on a Mavic...
View Article3.5-RC11 flying good on the Solo
@Pedals2Paddles wrote: I did a reset, recalibrated accel and compass, and flew two batteries. I test stabilize, alt hold, loiter, land, and RTL. I didn't have time to do much more, but it flew every...
View ArticleClik here to view.
Advice needed on where we are allowed to fly
@Perry_Cheng wrote: Drone Enthusiasts,So, I've just bought a Mavic Pro drone for several months and learning a lot about how to fly and are really excited to be able to take incredible pictures with...
View ArticlePixracer not detecting external compass
@matt88 wrote: I'm using 3.4.6 in the hexacopter variety. I have tried everything. Also using a m8n gps/compass combo and the gps works great however the compass is never detected? Tried switching out...
View ArticleInput channel redirection to gpio pins on flight mode
@gearwarrior wrote: I've been looking for a topic. I know someone has already thought of this or its already available, so I don't know how to put it into words. Basically, when you put the unit into...
View ArticleRC Output Mapping - PixRacer
@james_pattison wrote: G'day guys,I don't often post asking for help, but this one has me stumped.I'm putting together a new quad, with a PixRacer and 4-in-1 esc, set for oneshot125.The esc has a...
View ArticleQuad becomes unstable after mid-mission-land and takeoff again
@Jesper_Andersen wrote: I've searched for similar issues but haven't really been able to find anything even though this seems like a firmware bug that somebody else should have encountered. I've...
View ArticleHere+ RTK / Lost of GroundControl Connection / Failsafe / (EKF)
@Copter_Newbie wrote: Hi everybody, I would like to fly tomorrow with the "Here+ RTK" and my Pixhawk2.1 After a few minutes, I have an accuracy of about 1 meters. So, the MissionPlanner or Base will...
View Article